CJ-2A Research Archives

CJ-2A, cj2a

To Top

1946 CJ-2A Clinton, Ma eBay (stainless parts)

• CATEGORIES: CJ-2A • TAGS: , , This site contains affiliate links for which I may be compensated.

1946_cj2a_clintonUPDATE:  This is back on eBay

Here’s a fiberglass CJ-2A that also has a stainless steel grille and windshield.  This has a variety of updates.

“You are bidding on (1) 1946 Willys Jeep CJ2A.  I am the second owner of this vehicle.  The original owner worked on this jeep for 2 1/2 years. He has built many Willys Jeeps in the past. the entire chassis was disassembled Media blasted, boxed and repaired.  All welds are 100% pentrated TIG. The front of the chassis was removed and built up with a donor chassis from a jeep CJ5 donor. and 2″x2″ bar Stock.  The chassis was then painted with 2 coats of POR-15 and chassis coat.  A Rancho 2-1/2″ lift kit was installed along with an additional 1/2″ lift and greasable zirks for a total of 3″ lift.  This will easily clear 33″x12.5 tires.  The rear axle is a 1959 CJ5 Dana 44 that was rebuilt and in the front is the stock dana 27 that was rebuilt.  the gear ratio’s are 5:38.  the T-90 tranny and model 18 transfer case along with bearings, seals, and clutch were also rebuilt.  All new brakes front and rear as well as custom bent brake lines, rubbers, and a dual master cylinder kit.  It has the L-138 Flat head motor in it that was rebuilt and bored .040 over. it runs beautifullly.  It has also an aftermarket Solex carb and custom air intake kit.  it has been converted to a 12 volt system with a brand new alternator.  the body is all fiberglass built by AJ’s Body….”

 
To Top

1946 VEC CJ-2A Gridley, CA **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

1946_cj2a_gridleyUPDATE:  **SOLD** Was $4000

Here’s a fine looking early ’46 CJ-2A with the driver side cutouts.

“Straight CJ2A willys jeep mostly all original. L-head (flat head) four cylinder, Custom Cool air intake with K&N air filter , Remote spin on oil filter, GM alternator, Converted to 12 volt, Engine has been recently gone through, replaced rings, main and rod bearings, cam chain and sprocket. Auto machine shop polished crank and miked it, (still within stock tolerance)
Warn 8000lb wench….

 
To Top

1946 CJ-2A Fallbrook, CA **SOLD**

• CATEGORIES: CJ-2A, stainless/jewels • TAGS: This site contains affiliate links for which I may be compensated.

1946_cj2a_fallbrookUPDATE:  **SOLD** Was on eBay

“Small block 350; Muncie 4-Speed with Warner overdrive. Boxed frame. PRP seats. Small patch of rust on rear of right front fender. 9″ Ford drum brakes. Drives well. Has approximately 359 miles on odometer.”

 
To Top

1947 CJ-2A Detroit, Mi $3500

• CATEGORIES: CJ-2A • TAGS: , , This site contains affiliate links for which I may be compensated.

1947_cj2a_detroitUPDATE: The price has dropped to $3500

The paint job on this is interesting.  The bumper is pretty wild; I guess the jeep was used for pushing?

“The body is in good shape it runs and drives tires are good dont leak has a toe bar on the front with a custom front bumper.”

 
To Top

1948? CJ-2A Winstead, Mn $2,995

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1948_cj2a_winsteadA reader named Jim forwarded this interesting CJ-2A.  The body appears in very good shape.  It sports a column shift and a PTO.  It appears to have a CJ-3B windshield. With the 3 dash panels and the column shifting, I’d guess this (or part of it) is actually a mid 1946 rather than a 1948.

“GREAT WILLYS RUNS AND DRIVES GREAT 3SPD PTO WINCH TOW BAR 2 EXTRA SPARES NICE SHAPE TURNS ON A DIME WILL GO JUST ABOUT ANYWHERE TRADES WELCOME BRYAN”

 
To Top

1949 CJ-2A Fairfield, Tx **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1949_cj2a_fairfieldUPDATE: **SOLD** Was $950.

The back of this jeep appears to be solid.  I can’t tell for sure.  It also appears this jeep has a full floating rear end.  Obviously, the body has been modified a bit.

“49 Willys Jeep 950. obo as is.”

 
To Top

1947 CJ-2A West Slope, Co No Price

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1947_cj2a_westslopeI can’t tell much about the body  from the pics.

“i have a 1947 willys jeep in good shape, no rust on body or inside just bit under. has brand new engine with 40 miles on it and new transmission with 300 miles on it. front disc brakes, lockers front and back. with lockable hubs all four tires so you can tow it nice and easy and choose what tire you want to spin. im intrested in a bumper trailer or toyota motorhome.”

http://westslope.craigslist.org/bar/1079890706.html

 
To Top

1949 CJ-2A Tempe, Az eBay

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1949_cj3a_tempeUPDATE: Now on eBay. Many more pics and very detailed description — if only all sellers were so precise!

This jeep looks fantastic, but I am surprised someone would do all this work and not replace the 41 rear end with a Dana 44.  Note that this is the original tub, but the tailgate has been carefully removed.

“1949 Willys CJ-2A Jeep which has been mildly customized and modified for off-road and everyday usage around town. This Jeep has been professionally done with attention to detail and function, incorporating many modern upgrades yet still keeping the period CJ-2A look. Although this Jeep has the look and capabilities for serious off-roading it has never been driven on anything but hard surfaced highways. It has been re-powered with a Chevrolet 283 small block backed by Muncie 4-speed transmission and goes like a bat-out-of-hell, but has plenty of low-end torque for any situation.”

View all the pics on eBay

 
To Top

1946 CJ-2A Lakeview, OR **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1946_cj2a_lakeviewUPDATE: **SOLD** Was on eBay.

This looks like a nice CJ-2A.  It does have some rough spots on the rear left corner.

“1946 Willys CJ2A SN:53163 Clear Oregon title.  Jeep has had frame off restoration with some exceptions. Floors have been pached wear needed or replaced. Hat channels have been repaired wear needed or replaced. There are three thin spots that have been cleaned on the tub can be bondoed but I prefer not to use it. I have tried to leave as original as possible. Jeep is approx. 90% original, engine is out of a 49 Willys PU. Oil psi about 55 when operating 40 @ an idle. Approx. 200mi. on a new clutch, pressure plate and throw out bearing…..”

 
To Top

1948 CJ-2A Pullman, Wa $3000

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE:  The price rose from $3000 to $3500.  Still no pics. It’s been for sale since last April.

Here’s one I missed that’s in Pullman, Wa.  No pics were included in the Ad.

“I am selling my 1948 willies jeep. Been updated with a buick V-6 and tilt steering wheel. nice interior, seats are in great shape. The top is in good shape some stiches coming loose on the drivers door around the window. Great oversized tires on centerline rims. Diamond plating, spare tire and 2 jerry can fuel cans. The jeep runs great lots of power and would make an awesome restoration project. I was going to restore it but dont have the time. The body is straight and clean, very little surface rust and the floor boards are pretty solid. Also has a full roll bar. Might be a blast to drive this summer, heck who knows join a jeep club and tour the woods. It’s just a fun thing to drive. It has a new master cylinder but needs the slave cylinders replaced. I have checked and they are $8.95/ea. most jeep parts are pretty cheap.  Call for pics.  509-432-3952”

http://pullman.craigslist.org/car/629080281.html

 
To Top

1947 CJ-2A Grand Island, Ny eBay

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1947_cj2a_grandislandUPDATE:  This jeep is back on ebay.  Now also on Craigslist for $6500.

Here’s a 1947 CJ-2A with lots of pics on eBay. I keep thinking I’ve seen this one, but I couldn’t find it in a search of past posts.  Maybe it was bought and is being resold?

“Seats are Bestop Trailmax.  Low back height fit the small style of the Jeep.  Great Hot Rod look.  I had tried tall back seats with five point harnesses but they were too restricting and did not look proportional.  Lap belts are just the five point harnesses.  I just buckle them around the waist and just let the shoulder belts lay there….”

View the pics on eBay

http://buffalo.craigslist.org/cto/1080415062.html

 
To Top

Builds — David and friends

• CATEGORIES: Builds, CJ-2A, CJ-3A, Features This site contains affiliate links for which I may be compensated.

David and his friends transport themselves back in time each each fall by getting out their jeeps, heading to the woods, and cleaning brush, trees and other obstacles out of the way in preparation for winter snowmobiling in New York.

David’s owned his (the gray ’51 CJ-3A) for six years.  His friends have owned their 1947 CJ-2A and 1949 CJ-3A for about 25 years.  Thanks for sharing David.

david_wyre4

Continue reading

 
To Top

1947 CJ-2A Crystal Lake, IL **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6000.  Better pics now.

Nice looking CJ-2A.  It looks like there isn’t a tailgate, but I can’t tell for sure from the pics.

“1947 Willys CJ2-A. Semi-Pro restoration about 10 years ago, clear & clean title. Orginal L-Head motor, 3 speed on the floor. 4×4 (works great too!) Nice 31×15 inch General tires w/ rancho shocks. What Ive added (since Ive owned it). Brand new speedo (shows two hundred sixty-some miles)Sun Pro Tach, Cobra CB Radio w/ 102 rear bumper mounted antenna. AIWA Cd player w/ MP3 jack & speakers (NOT permanant – only zip-tied). Electric radiator fan w/ switch on dash. Front bumper mount off road lights (easily removable). Oil change at start of summer, new plugs, just replaced the entire fuel line from tank to fuel bowl (and new fuel filter). She does run very well, however she will not do a DIME over 55mph (and thats pushing it!)…”

 
To Top

1947 CJ-2A Apache Junction, AZ **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1947_cj2a_apachejunctionUPDATE: **SOLD** Was $5750.

This CJ-2A looks well built.  The chev 350 and radiator are neatly placed into the engine compartment without modifying the fenders. It’s got a good looking roll cage as well.

“47 Willys. 350 crate with a 350 turbo trans. 4.27 detroit locker with 33×12.5 BFG. Asking $5750.00 OBO”

 
To Top

1947 CJ-2A Kemblesville, Pa $8600

• CATEGORIES: CJ-2A • TAGS: , , This site contains affiliate links for which I may be compensated.

UPDATE:  The price has risen to $8600.

The price is on the high side, but it appears in great shape.  Check out the original top.

“Thsi rust-free Jeep has a 4 cylinder engine and 3 speed transmission with overdrive; hi/lo range and 4 wheel drive with lockout hubs. It has 12 forward speeds with the overdrive and can cruise along at highway speeds.It has the original type top with removable doors; a back seat; dual windshield wipers; a radio, heater and defroster fan. In all- about $3000.00 worth of option”

 
To Top

1948 CJ-2A Italy, Tx $3500

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1948_cj2a_italySomething appears to have been done to the bumper, but otherwise this looks like it could make a great, pretty easy restoration project.

“This is a very collectable 1948 CJ2A Jeep Willys- I am firm on the price of this 60 year old vehicle. It runs good and has the original engine. I have done some restoration which includes:
New brakes and brake lines, new gas tank, new carberator and tune up, new muffler and tail pipe. This has all of the original frame an body matching numbers. This would be a great restoration vehicle and fun to drive in parades or around the farm or ranch. Serious inquiries only- 214-797-0911”

http://dallas.craigslist.org/sdf/cto/1071139848.html

 
To Top

1948 CJ-2A Baytown, Tx **SOLD**

• CATEGORIES: CJ-2A • TAGS: , , This site contains affiliate links for which I may be compensated.

1948_cj2a_baytownUPDATE: **SOLD** Was $995.

Yeah, it’s a bit rough.  But, how can you not love the top?

“This is a 1948 Willys Jeep, ran until parked after last winter hunting season. Have a spare motor that goes with it for parts. The WINCH is not INCLUDED :o) The towing bar is included.
e-mail with any questions. $995.00 OBO”

 
To Top

1949 CJ-2A Russellville, AR **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

1949_cj2a_alabamaUPDATE: **SOLD** Was on eBay.

This appears to be in pretty good condition. The seller is trying to claim mileage of only 5800, but I’m very sure that’s a replacement speedometer (as are several of the other gauges).  I suspect the front turn signals/pking lights are after market as well.

“What an amazing vehicle!  This jeep was given to a Tennessee Forrest Ranger as a retirement gift, and he held onto it unitl I bought it  3 months ago!  It runs out really well…has new tires…a working original WENCH and PTO GEARS underneath for FARM ATTACHMENTS… The engine is a HURRICANE 4 cyl with 3 speed transmission…4WD…5800 ORIGINAL miles and the ORIGINAL PAINT, as well…I’ve been through many jeeps, and I have to say that I’ve never seen another like this!  it’s truly ONE-OF-A-KIND!”

 
To Top

1946 CJ-2A CDA, Idaho eBay

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1946_cj2a_cdaThere appears to be no reserve on this.  There’s been a good deal of work done on this rock crawler.  The grille and lights are a bit odd though.

“Body:     1946 Willys CJ2A, with a full custom built roll cage. Motor:     350 Chev. ( Came out of a 1979 Chev P/U), Trans:     4 speed  sm 420, Transfer Case:   Dana 20 Transfer Case, Rear Axle:     Dana 60 Rear axle with a welded spider gear, 6.17 ring and pinion, Front Axle:   Dana 60 with a lockright locker, Disc brakes, Chromoly shortside inner and outer shafts, 6.17 Ring and Pinion …”

View all the pics on eBay

 
To Top

Flat Fender Monster Truck Marengo, Oh $44,000

• CATEGORIES: CJ-2A, Unusual This site contains affiliate links for which I may be compensated.

willys_monstertruck_marengoI don’t know what these are worth, but you don’t see these everyday.

“TOO MANY FEATURES TO MENTION, PICS ARE BEFORE CUSTOM PAINT JOB, ALSO HAVE LARGER MUD TIRES W/ CUSTOM RIMS, EVEN HAS CUSTOM PTO FOR PROPELLOR IF YOU WANT TO DRIVE IT INTO WATER, NEED TO SELL ASAP $44,000 not a misprint, It’s a full size toy for men! CALL MONTY 419-253-8631”

http://columbus.craigslist.org/cto/1060914213.html

 
To Top

1946 CJ-2A (mb?) Avenal, Ca $3000

• CATEGORIES: CJ-2A, GPW (Ford MB), MB This site contains affiliate links for which I may be compensated.

1946_cj2a_avenalUPDATE:  Price dropped to $3000

With the driver side indents and the lack of tailgate, this certainly looks like an MB/GPW to me.  Note the phone number is missing a digit.

“nice jeep …runs ok…have done some basic work on it…used it for deer season last year and now we are moving….got to much stuff has original straight 4 cylinder ….has 4 new bi-directional military tires,new battery,new plugs, cap,rotor and points new coil and 12 volt head lights….12 volt conversion with altenator… call 559-816-960.”

http://fresno.craigslist.org/cto/1061328312.html

 
To Top

1947 CJ-2A Racine, Wi $6500

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1947_cj2a_racineThis CJ-2A has a fiberglass body.  The roll bar is attached to the back wheel wells.  I’m pretty sure that’s not a good idea.

“1947 Willys CJ2A Jeep, clear Illinois title. Runs great 4WD works, restored about 10 years ago, fiberglass body, x-tra parts that go with it. ALWAYS stored indoors!! Ready to go for spring, get’s lots of looks!! Price is negotiable, would consider trade for Grand Marquis, or Crown Victoria or ??. Let me know what you got? I’m about 1/2 hour from the Wisconsin border. Call with questions 815-403-6895 – ask for Ryan.”

http://racine.craigslist.org/cto/1059469826.html

 
To Top

1947 CJ-2A Port Orchard, WA **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Was $400. **SOLD**

Here’s a parts jeep.  With the Dana 30 front and AMC 20 rear.  The paint job is unusual.  The back of this body appears solid (no tailgate).  I’m wondering if that’s a DJ body.

“1947 Flat Fender Willy’s Jeep CJ 2A with roll cage. No transmission/transfercase. Mounts for small-block Ford (289 / 302). Original axles plus Dana 30 front and AMC 20 rear. Need the space more than I need the Jeep. $400 / obo.”

1947_cj2a_portorchard

 
To Top

1946 CJ-2A Independance, Mo eBay

• CATEGORIES: CJ-2A, Unusual This site contains affiliate links for which I may be compensated.

1946_cj2a_independanceHere’s a very usual jeep.

“No title, strickly trail rig, Motor trans and transfer case all work good. dana 44 front and dana60 in rear with 488 gears. four link rear 3link front. Full hydraulic steering no sterring box.5 point harness x2 in front. winch mount, 700r4 trans, lockouts, axles are welded, needs brake booster or master cylinder. I will need a $500.00 deposit within 24 hours of end of auction.”

View all the pics on eBay

 
To Top

Builds — CJ-2A Body and Frame Work by Mike

• CATEGORIES: Builds, CJ-2A, Website This site contains affiliate links for which I may be compensated.

mike_rebuildI ran across some extensively photographed and discussed body and framework (boxing in the frame) on the CJ-2A page forums.  There are plenty of pics and four or more videos.  There’s also some interesting discussions about dealing with hat channels:  to fill or not to fill, that is the question (page 3 of the forum). So, if you are doing some body work on a CJ-2A, you’ll find this interesting.

The pic on the right show’s Mike’s first attempt at welding thin body metal.  After some additional grinding and filler it looks like it will turn out great.

View the all information at the ‘started body work’ topic on the CJ-2A Page forum