To Top

1946 CJ-2A Sahaurita, Az $2700

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

It’s hard to tell much from the pic.

“1946 Willys CJ-2A. Original drivetrain with flathead four cylinder engine. Clear AZ title, not registered. Body has some rust but it has mostly been repaired (needs paint).
Comes with towbar, removeable shade (golf cart top that clamps to the roll bar), and service manual.
Many upgraded and/or new parts within last several years (the Jeep has rarely been used during this time):

– Transmission (three speed) and transfer case rebuilt
– Steering box rebuilt with all new parts, one-piece tie rod conversion, new steering wheel
– Brand new gear-reduction starter
– 12V electrical system with GM alternator, headlights work
– Flush-mount taillights installed but not hooked up
– Carburetor rebuilt, adjustable fuel pressure regulator
– 7.00-15 tires (much easier to find then original 6.00-16)
– Rebuilt master cylinder, and new wheel cylinders
– Re-lined transmission parking brake and new cable (comes with it but not installed yet)

I have owned it for eleven years and used it for hunting and four-wheeling. It could be made street-legal fairly easily, but with 60 hp, 9″ brakes and 5.38 gears it is much better suited for off-road use.
I am selling it because I no longer use it and have too many vehicles. I will consider offers, and will also consider a trade for a big quad or a smaller RV travel trailer (no cars or trucks,etc). Please respond via craigslist or call Al at 490-1963. I can send several other pictures upon request.”

http://tucson.craigslist.org/cto/1519534019.html

1946_cj2a_sahurita

 
To Top

1945 MB Covina, CA **SOLD**

• CATEGORIES: MB • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6000

This jeep has toyota running gear.  It looks like a good conversion.

“Recently rebuilt and restored with all Toyota running gear. 22R 4cyl. 5 spd. trans., PS, PB, tow bar, full top with doors, new gauges, new gas tank.”

1945_mb_covina

 
To Top

1953 CJ-3B Morristown, TN **SOLD*

• CATEGORIES: CJ-3B • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $800.

The seller has added additional information in the Q and A section.  It appears mostly stock, except for the L Head.

“This is a ’53 Willys Jeep that has been in my family for many years and was in running condition when parked in the barn about five years ago.It has it’s original Hurricane flat head four cylinder engine that always ran really good and I’m sure it would again with a little TLC.This Jeep has not been off of my family’s farm in over twenty years and is still in pretty solid shape as it has always been kept in the barn.I can’t guarantee it’s mechanical condition but would only imagine it would still run with a little work.Thanks for looking and good luck!”

1953_cj3b_morristown1

1953_cj3b_morristown2

1953_cj3b_morristown3

1953_cj3b_morristown4

1953_cj3b_morristown5

 
To Top

1946 CJ-2A Canton, Ga **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $800.

“1946 Willys CJ2A – I never have had the time or money to restore this Jeep. This Jeep has an International 4 cylinder engine in it (not original). I had the engine running in 2000, but blew a gasket or something and haven’t done anything to it since then. If you are interested in a restoration project or building a great offroad machine, this would be great for either. Body has minor surface rust and some bad bondo from previous owner. Additionally, new floor pans were installed at some point. Come and take a look. I will try to put up pictures at some point – it currently is serving as a shelf in my garage so not very photo worthy!”

1946_cj2a_canton

 
To Top

1953 CJ-3B Santa Clarita, Ca **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

1953_cj3a_santaclaritaUPDATE:  **SOLD** Was $6500

“First year of the willys high hood. Jeep has Buik 225ci v6 conversion kit, with a Warn overdrive. 33inch Tires, jeep has air compressor under the hood, which when activated fills the rear bumber compressor resevoir to 120lbs. Rear bumber has pneumatic hose fittings and preassure gages. Brand new master cylinder, brand new clutch, brand new sending unit, brand new front axel, and has a brand new starter. Jeep has locking tool boxes in the rear. Bmw bucket seats 5point restraint seatbelts. Jeep has air horn under the hood (Very loud). Rolls down freeway 70mph no problem. Rear locking and unlocking hubs so jeep may be towed behind motorhome. Comes with softop, softdoors, and towbar. Fully padded roll cage, tilt steering. Jeep runs excellent, two five gallon spare gas tanks mounted behind spare tire on back of jeep. After market heater installed. Jeep still has originall manufatures plate under the hood.

 
To Top

1952 M-38 Eatonville, Wa $7000

• CATEGORIES: M-38 • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE:  Price dropped to $7000

Lots of nice upgrades and changes. For stainless lovers, note the stainless parts.

“This Jeep is set up for Trail or Street. It has Detroit lockers, Dana’s, Fuel cell with Floating pick up, 225 Buick with Holley carb, Stainless Steel Hood, Windshield Frame, and Grill. It also has Best Top Bucket Seats, Warn 8,000lb winch, Warn Overdrive, Power steering, Disc Brakes with Power Locks, and Super Swampers on Ultra Polished 10″ Wheels. Lots of Accessories. Call Tim @ 253-651-7977.”

http://seattle.craigslist.org/tac/cto/1519572860.html

1952_m38_eatonville3

 
To Top

Christmas Tree MB $12.99 on eBay

• CATEGORIES: toys This site contains affiliate links for which I may be compensated.

Looking for that perfect tree ornament?  Maybe this is what you need.

“Metal Die Cast Body, 1940’s Army Willys Jeep. Awesome detailing throughout.
Metal 3′ Inch Long Ornament Hook For Hanging Will Be Included. Cars Come from Several Collectible Toy Die Cast Car Companies. Shipping Will Be $5.65. USPS *Priority Mail* With Tracking Number To Insure Fast Delivery. We Only Charge Actual Shipping Costs. I Combine Shipping On Multiple Cars. *If There’s A Problem Once Your Item Arrives, Please Contact Us Before Leaving Unfavorable Feedback And We Will Make Things Right.”

View all the pics on eBay

MB_ornament

 
To Top

Wanted: WWII Jeeps and Parts Herald, Ca

• CATEGORIES: wanted This site contains affiliate links for which I may be compensated.

Here’s a buyer looking for WWII parts and jeeps.

“I am looking, WANTED, any and all parts for the old World War 2 JEEPS, either Ford or Willys. Anything you might have from say a generator/ starter all the way up to a basket case not running. Shoot me some pictures and a price you are looking to get. Have trailer with winch and cash. Thanks flansam@softcom.net”

http://stockton.craigslist.org/pts/1514139297.html

 
To Top

1956 CJ-5 Sweet Home, Or $2000

• CATEGORIES: CJ5 • TAGS: This site contains affiliate links for which I may be compensated.

This has a rebuilt engine.  It looks pretty stock and in good condition except for the paint.

“1956 Willys Jeep. Newly rebuilt engine, new tires and wheels spare to, drives and runs great. DO NOT respond via cragslist as this post is for a freind. Call Rob at 541-367-1346.”

http://corvallis.craigslist.org/cto/1519064851.html

1956_cj5_sweethome

 
To Top

Wanted: 3A Parts and a complete 2A, 3A or 5 Portland, Or

• CATEGORIES: wanted This site contains affiliate links for which I may be compensated.

Here’s a buyer looking for both parts and a whole jeep.

“looking for transfer case, complete 3a L124 engine, and other misc parts. Also looking to buy a complete 3a, 4a, or cj5 in origional condition, suitabe for restoration.”

http://portland.craigslist.org/mlt/pts/1519038155.html

 
To Top

1960 Willys Wagon Port Townsend, WA **SOLD**

• CATEGORIES: Willys Wagons • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: Was $5000. **SOLD**

I just love the fact that this was the seller’s daily driver for years.

“My maroon Willys station wagon that has been around Port Townsend for the last eighteen years (parked in front of Hilltop Texaco for five of those) is now for sale for $5000. This was my daily driver until five years ago when I decided to make it 4 wheel drive. I have collected and built absolutely the best components to accomplish that but too many other projects have taken over my time. It currently has a tired but functional Chev 350 and a turbo 350 tranny with a Lokar shifter with e-brake and a positraction Dana 44 rear. I just installed the rechromed bumpers, the rest of the chrome is good. The wood runners in the back are in excellent condition also. It has the hard to find original seats that I reupholstered several years ago. Components that I have to go with it are; rebuilt 700R4 trans that was mated to a NP 205 (all gear, no chain) transfer case, Dana 44 front and rear differentials, new loaded calipers for the front, Advance adapters Saginaw power steering kit, an extra set of five original 16 inch wheels with old Michelin tires on them, a new tailgate hinge and tailgate lower repair section (which it really does not need) and a complete rear clip from a “barn door” (side opening doors) vehicle. I have collected boxes and boxes of spare things like speedometers, door handles, windows, steering wheels and so much other stuff that I can’t remember all of it. ”

1960_wagon_porttownsend

 
To Top

1953 Wagon Oakdale, CA **SOLD**

• CATEGORIES: Willys Wagons This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1500

This is sort of running.

“53 willys 350 motor runs 350 tranny b&m shifter need somee tlc like some windows are busted out seat covers and the stearing hooked up real easy i have bill of sale and can deliever if gas is covered will trade for another good runing car or bike or cash vw chevy ford pre 75 cars or a good cars”

 

1953_wagon_oakdale

 
To Top

1959 DJ-3A Redlands, Fl $1175

• CATEGORIES: DJ-3A This site contains affiliate links for which I may be compensated.

UPDATE:  Price dropped to $1175

(11/7/09) You can’t say this seller hasn’t tried to give you a complete overview of this jeep.  There is a total of 37 images.  It’s rough, but it is a column shift 2 wheel drive with a tailgate.  It’s supposed to run well.

“Willys Jeep dj3a Overland this is the 2 wheel drive model with L-134 engine with three speed on the column.  Not just a L-134 engine but a industrial L-134 engine.  This engine runs real good as you can see in the video plus the oil is super clean like someone went through this engine.  As you can see in the video I pulled the dipstick out and you can see how clean the oil is. And that was after a half an hour of running plus driving it in the yard….”

http://miami.craigslist.org/mdc/cto/1518173738.html

1959_dj3a_redlands

 
To Top

Converto Airborne Dump Trailer Jeep WW2 **SOLD**

• CATEGORIES: trailer This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was on eBay.

“This WW2 trailer was originally design for the U.S. Army Corp of Engineers to be used as both a general purpose cargo trailer much like the Willys MBT/ Bantam T3 and specifically for use beyond the capability of the MBT/T3’s; for moving and dumping material. It is estimated that there were about 6500 of these trailers produced during WW2 and is ideally pulled by a Ford GPW or Willys MB jeep or a dozer.

airborne_trailer1

airborne_trailer6

airborne_trailer5

airborne_trailer2

airborne_trailer9

airborne_trailer3

airborne_trailer4

airborne_trailer8

The Dump action is controlled by the middle lever which tilts the bed. The side lever directly under the data plate controls the tailgate itself. When the side lever is pulled the tailgate swings out from the bottom. It’s also possible to pull the top pins and fold it down from the top or remove the tailgate completely. The dump levers can actually operated from the drivers seat of a jeep by pulling on the rope which the end loop rests on the base of the shifter. So the load is not accidently dumped, both the bed tilt and the tailgate mechanism have safety pins. Also the tailgate has a small gate which exposes a circular hole to pour out smaller amounts of material or can be a port for a nozzle to distribute liquids in their own container. Another unique feature of the trailer is the bed itself can be detached by pulling the two large dump pins and driving away. *Notably the trailer did not come with fenders from the factory

“This particular trailer is very complete and has all the important components typically missing: -Original tailgate -pins and chains -Thick lunette -Reinforced combat rims
-landing leg -Both cast dump latches -Dump levers”

For a 60+ year old trailer the trailer is in truly amazing condition. It is incredibly straight and solid. There are literally only 3 or 4 dents or dings in the entire trailer and no bowed panels. This trailer is one of the finest examples of these trailers I have ever seen. Unlike the few other Converto dump trailers I have seen or owned. The the panels and pieces where lined up very well for assembly from the factory; the original welds are clean and almost uniform. Considerable effort was made to make this trailer as correct as possible with attention to the smallest details Including hand brushing the blue drab USA Number. The document pouch, data plate, custom rivets, pins, and chains where created or obtained to match the original. Body filler was not used in the preservation and there are only a few small flaws. The front (not the entire) of the bed is bit pitted (this can be seen in the pictures with the manual), there are three smaller than a pencil size holes by the tailgate round hole gate, there are a few small flaws in my paint job and as mentioned there are three small dents all smaller then a quarter one in each top rail and one in the bed. Again this is one is very solid and complete.

The trailer has recently received:  -A Very hard to find NOS US ARMY Corp of Engineers document pouch with custom rivets -original pointed tread Goodyear 6.00×16 NDT tires -three wire cloth inter-vehicular cable composed of NOS components -NOS BO light switch -CB taillights -All NOS lights -reflectors
-NEW Wiring Harness from Vintage wiring of Maine – a few new pins and chains -Reinforced combat rims -TM5-9084 with supplement -Data plate from Robert de Ruyter www.dataplates4u.com -New Paint -hand Brushed Markings in blue drab -Trailer Dump lever rope “

 
To Top

1948 CJ-2A Project Meridian Ranch, Co $300

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE:  Price dropped to $300

(12/01/09) Lots of work needed on this project.

“I bought this Jeep with the intention of restoring it, but due to the economy and the possibility of no longer having a job I need to sell it. I am asking for $300. At this point it is in pieces.”

http://cosprings.craigslist.org/cto/1518443591.html

1948_cj2a_meridianranch

 
To Top

3 Flat Fender Projects Wenatchee, Wa

• CATEGORIES: CJ-2A, CJ-3A This site contains affiliate links for which I may be compensated.

There’s a variety of parts and projects here with prices that vary.

“1st jeep has the most potential and while the picture does not show it, it has a grille and other parts that can be put together to make a good one. It has rear diamond plate for the corners and diamond plate for the sides. It does have a windshield that needs put together. No seats or titles on any of them. It has saginaw front end which is optional I will keep it if you want to dicker. If you plan to install a bigger engine I will keep the engine and transmission and transfer case too. Engine is a L head than turns over by hand but someone got the carb and starter. It has a roll bar of sorts. Price depends on if you want the saginaw and engine. $300 with out all that. $650 with all that.

2nd jeep is a basket case and frames front has cracked totally off. But it has a round cross bar that can be used on the first jeep that some idiot cut off the original and put L iron to fit the saginaw on it. Or you can weld it back together and start a rebuild of a second jeep. it has axles but no power plant or transmission or transfer case. $150 for it.

The third is just a body and hood. It was a rare long body that someone cut down to a CJ3A size. Welds need to be finished on that part. Body could be used on one of the other two if you wanted. Might have another windshield in need of repair for it too. $200 for it.

As I said no titles but they can be gotten. I believe data tags are on one at least. I have extrea transfer cases that may need rebuild for $100. And some other extra parts for those that buy all three of them. Including axles. Have other small parts that I will make deal on if you buy all. I just need parts to finish my 2A. Might consider trading for things I need for the 2A like seats or guns or other old interesting item. Especially jeep PTO’s for the front and back or an overdrive. Or Jeepster parts from 48 and 49. I am keeping the roll cage for the 3A for now. But with the right offer will sell it too. It is one that is done well with sides that fit the contour of the CJ2 and 3A frame. $450. These are projects as you can see. And as I said I have hundreds of various small parts too for sale. And for the right trade or take all I will think about a better deal. Also have a F head that needs gone through. It used to turn over by hand but now doesn’t. has a regular oil filter system on it for spinning oil filters and upgraded carb. Long story. $250. Had it in a flat fender and it ran then.

http://wenatchee.craigslist.org/cto/1517486759.html

various_projects_wenatchee

 
To Top

1953 CJ-3B Northern Michigan $8900

• CATEGORIES: CJ-3B • TAGS: This site contains affiliate links for which I may be compensated.

This appears to be a very nice rebuild and update.  There’s lots to like here.

“This jeep will most likely not be your regular driver. I have rebuilt it from the frame up. Frame has rubberized paint. Set on a 3″ Rancho 9000 suspension. New 32″x11.5″Dayton A/T. Body parts are all origanal, again rubberized under coating. Tub has herculiner coating on inside. All new 12v Electrical system. Performance ignition. Power steering. Front shackle reversal kit. 12gl. custom rear gas tank. Rebuilt orig. 3speed. Dana 27 fr. Dana 44 rear.w/ 4:88 gears. Professional rebuilt buick 231ci.(3.8L) All performance parts B&B. Holley Demon Carb. Custom dual inner frame exhaust w/ coated headers. Also comes w/ 2 tops Soft vinyl and steel hard. Spent a lot of time and money on this machine and I am not going to do any leg work for the buyer to sell this. If you would like more info e-mail me bigkash@yahoo.com ps. I am only trying to sell the jeep NO SPAM please”

http://nmi.craigslist.org/cto/1517231764.html

1953_cj3b_northernmichigan

 
To Top

1953 M-38a1 Gilford, NH $3500

• CATEGORIES: M-38A1 • TAGS: , This site contains affiliate links for which I may be compensated.

This looks in good shape, though the seller’s camera appears to have a smudge right in the center of the lense.

Good running and not bad looking Antique jeep .Take it in to a parade like it is or do a complete restoration. It is a good solid start either way. New brakes & tune up. Ready to enjoy. Please call between 4 & 8 pm. I work early every day…. Thanks…Bill 603-293-0685″

http://nh.craigslist.org/cto/1517624607.html

1953_m38a1_gilford

 
To Top

1958 Truck Albuquerque, Nm $900

• CATEGORIES: Willys Trucks This site contains affiliate links for which I may be compensated.

No pics, but this is a strong running truck (according to the owner).

“1958 willys truck with title, 6 cylinder engine 3 speed transmission, engine was rebuilt some time ago, 4×4 works good use it this year at Mt. Taylor last year for me hunting getting to old , pretty much all original body need a little work, dark green paint is ok, brakes work good , just had the heater core replaced so it does have a good heater for the winter, bought tires brand new a year ago, will drive at 55mph all day long even the light work I change it over to 12 volt system, the old 6 volt was just to weak, need to sell, $900.00 or best offer. sorry no pictures at this time email for an appointment .”

http://denver.craigslist.org/cto/1518008967.html

 
To Top

1948 CJ-2A Hudson Valley, NY **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $300

Check out the front of this frame.  There’s been some strange changes to it.

“48 cj2a frame is broken in the front. the motor turns over, has complete drivetrain,tranny and transfercase. Has four orignal rims. good axles and springs.”

1948_cj2a_hudsonvalley

 
To Top

1946 VEC CJ-2A Pueblo, Co **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3000

It’s an unusual color scheme.  It looks in solid shape and will likely make a great restoration.

1946 Willys Jeep, all original. This Jeep has been in storage for many years and not started. It has also been owned by the same family for over 40 years.”

1946_cj2a_denver5

 
To Top

1952 Wagon Flintville, AL **SOLD**

• CATEGORIES: Willys Wagons This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1000

“Great project vehicle, cool looking (reminds me of MASH) 1952 Willys 4×4 Station Wagon. Has adapter and mounts for SBC. Minimal rust for a ’52 model. Sold AS IS on a Bill of Sale. First $1000 or will trade for Ford powered vehicle: need work truck, Mustang, Fairlane, car trailer, mig welder, etc.”

1952_wagon_flintville

 
To Top

1963 CJ-3B Hurst, TX **SOLD**

• CATEGORIES: CJ-3B • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3250

This appears to be in very original shape.

“1963 WILLYS CJ3B, VERY GOOD CONDITION, CLEAR TEXAS TITLE, RUNNING AND 90%+ ORIGINAL, STORED IN BARN SINCE 1974, $3,200.00, DALLAS/FORT WORTH”

1963_cj3b_brumbaugh

1963_cj3b_brumbaugh2

 
To Top

Builds: 1951 M-38 in Santa Rosa

• CATEGORIES: Builds This site contains affiliate links for which I may be compensated.

While trolling for some M-38 information I discovered this build.  The owner is slowly attempting to return this to original condition of some sort.  As you can see, in the first pic below, an early step was to tone down the paint color.

Learn what the owner has been doing to this jeep.

1951_m38_santarosa1

1951_m38_santarosa2

1951_m38_santarosa3

 
To Top

1952 M-38 Waxahachie, TX **SOLD**

• CATEGORIES: M-38 • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $7500.

I’m not sure if this is still for sale or not.  What caught my eye, was that strange item attached to the front of the bumper.  Anyone know what that is?

“VIN number 66800”

1952_m38_texas1

1952_m38_texas2

1952_m38_texas8

1952_m38_texas10