To Top

Race Jeep Yelm, Wa $1200

• CATEGORIES: Racing This site contains affiliate links for which I may be compensated.

UPDATE:  The price is now $1200

This is a jeep designed for PNW4WDA racing.  This jeep has Formula desert dogs on the rear, but I can’t tell what tires are on the front.  The front shackles are reversed.  The front clip is all one piece (likely fiberglass).  It looks like the body is just a partial metal shell.  This jeep should also have a scattershield bellhousing (a requirement for racing).  This also appears to have chrome tie rods and a chrome front housing cover.  I wouldn’t be surprised if the rear was either locked or welded, perhaps the front as well.  This is actually a pretty good price if you want to get started racing in the PNW.

“Race Jeep. Buick V-6. T-14 Tranny. Spicer 18 44 Rear 27 Front. Needs some work. Runs and drives. $1200.00 OBO. Contact Kris @ (253) 219-2208.”

http://seattle.craigslist.org/oly/cto/814723102.html

 
To Top

My Build — The hood vs. the air cleaner

• CATEGORIES: Biscuit, Features This site contains affiliate links for which I may be compensated.

One of the issue’s I’ve put off until now has been the air cleaner.  I knew fitting an air cleaner between the hood and carb would be tight, a consequence of the tall Kenne Bell intake manifold.  However, I thought I might sneak it in there, but after finally fitting the hood onto the front clip, I discovered that even a low profile air cleaner won’t fit.  Unfortunately, the engine can’t drop much more (not that I want to drop and reweld the engine mounts for an extra 1 1/2 inches).  The only solution left (that I could think of) was to put a bump into the hood.  I REALLY didn’t want to do it.  But, I need to keep moving forward on this project, so I decided it was the most expedient solution.

Once decided, I then had to decide the type of bump.  After mulling it over, I chose to do a simple bump that follows the lines of the hood.  The first step was cutting the hole in the hood.  Next, I created a form out of a 2×4, putting a 20 degree edge, the same degree, but opposite, of the angle of the stripe on the body.  I laid two coats of fiberglass and resin and let it setup.  The good news is that the results are even and the angles correct.  The bad news is that I’m not thrilled with the results.  I’ve thought about adding some angles to the front to make the bump more interesting, but I think I’ll keep it simple and save the details for version 2 of the hood.

Here’s the hood precut

Here’s the hood with 3 sides cut.  I used a cutting wheel to do the cuts and a flat piece of steel as a guide to create a straight line.

Continue reading

 
To Top

1953 M-38A1 San Mateo, Ca $1500

• CATEGORIES: M-38A1 This site contains affiliate links for which I may be compensated.

Here's a labor day weekend deal. If the only problems really are a water pump making noise and brakes that need attention, then this is a great price.  It's worth a look if you are looking for a m-38a1.

" For Sale: 1953 Willys Military Jeep M38A1/CJ2A: This is a Labor Day Week End Sale! And just in time for deer season. The price is: $1500.00 dollars. This is a great deal for someone who is looking for an older reliable jeep and a part of history. All drive train in good shape, Engine, Transmission, Transfer case, rear end and front wheel drive. Clear California title, and is currently registered. Warn hubs on front wheel drive. Thor PTO Winch with about 100’ feet of 3/8” cable (works great).  Jeep Cons: needs a water pump (Water pump bearing is starting to make noise) and brakes will need attention (Leak in master cylinder). Jeep runs very well, fun to drive, and starts right up. If you are interested in this jeep please call (650) 347-8434 (home) or (650) 504-0920 (cell) Thanks, Phil."

http://sfbay.craigslist.org/pen/cto/818277073.html

 
To Top

1942 MB Smith River, Ca eBay

• CATEGORIES: GPW (Ford MB), MB This site contains affiliate links for which I may be compensated.

This jeep is located on the Oregon/Cali border near highway 101, so the drive alone is worth getting the jeep.  This doesn't look in too bad of shape.  The seller describes the body as fair to poor, but I've seen many worse bodies than this one.

"Body: Fair to poor condition, areas of rust.Engine: Has not run in 5 years.Tires: 5 in good condition.Other: Fenders & gas tank in good condition.Many usable parts if full restoration is not your thing.Shipping/Transportation will be the buyers responsibilityI'm located in California two miles south of the Oregon border on highway 101. I can be reached at (707)487-5808"

View all the pics on eBay 

 
To Top

1950 CJV-35U Stewartville, MN **SOLD**

• CATEGORIES: M-38 • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was on eBay..

“1950 WILLYS JEEP, VERY RARE NAVY AIRFORCE RADIO BEACH LANDING FORWARD COMMUNICATION UNIT ORIGINALY.  HAS LIFTING LOOPS FRONT AND REAR FOR HELICOPTER OR CRANE LIFTING. IT IS IN VERY GOOD CONDITION AND RUNS AND DRIVES VERY NICE.  STUDY THE PHOTO’S AND SEE FOR YOURSELF.  TIRES ARE GREAT, STEERS LIKE NEW, AND RUNS QUIET WITH NEW MUFFLER.  THE SEATS ARE GOOD, THE ENGINE HAS PLENTY OF POWER FOR OFF ROAD PLUS A GREAT PARADE UNIT AND JUST CRUISING AROUND TOWN OR ON THE HIGHWAY.”

 
To Top

1953 CJ-3B Durango, Co **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE: SOLD, but not picked up yet …

I think there is lots of life left in this CJ-3B, as much of it looks straight and in good condition. However, I would like a closer look at the front bumper area, as that bumper angles a little bit too much.

“I’m selling this 1953 Willys Jeep CJ3B for a friend and neighbor of mine. He’s drove it for as is for a long time. In December last year he pulled the stock T90 transmission to rebuild it as it sometimes popped out of third gear when accelerating. A huge storm hit, dumping so much snow it crushed his garage barely missing the Jeep. Would be a very good, inexpensive project for the right person. I will try to be as detailed and candid as possible but feel free to ask questions and I will answer as quickly as I can. Has a 289 Ford small block under the hood, add a battery, antifreeze and its a runner again. Has been converted to Saginaw steering, with column, box etc. steers easy. Stock running gear behind the engine, T90, spicer 18, stock axles etc. Still has good brakes, has only been sitting since Christmas rather than years in a back field like so many out there…”

**SOLD**

 
To Top

1948 CJ-2A Eugene, OR **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1599

Given this is a non-running project that has had some mods done to it, the price is a little high.  I don’t see any obvious rust on the body and the back looks pretty straight, but I can’t see much more from these pics.

“1948 Willys cj2a project needs a new home. Not running. Needs starter. Painless wiring kit partially installed. New gauges. New ignition switch. Do not have time to complete. Must sell”

 
To Top

1953 CJ-3A Chico, Ca $1750 OBO

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

There are three pictures of this jeep.  Two I *think* are before it was torn down and the third looks like it is an in-progress rebuild.  In the third picture, shown to the right, you'll note newer rims and how the body is sitting higher than before (could be a new SOA mod or different springs).

"1953 Willys Jeep CJ3B Project 231 buick V6 stock axles trany been gone thru tube frame vary clean 1 1/2 Body left missing some parts great potential. fairly clean body. call 530-228-1763 Mark / 530-877-1663 1750– OBO e-mail mdwight@c21selectgroup.com"

http://chico.craigslist.org/pts/812373250.html 

 
To Top

My Build — Hood Mounted

• CATEGORIES: Biscuit, Features This site contains affiliate links for which I may be compensated.

Last night i got the hood mounted, trimmed and latched. Once I determine where to mount the blocks (not sure what I'm going to make those out of yet), then it will be ready to patch, sand and paint.  

 
To Top

1953 CJ-3B Melba, Id $3500

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE:  The price is now $3500

I'm not sure I have seen a jeep with a stainless steel roll cage.

"1953 Willys high hood jeep. Dana 60 rear end, detroit locker. 360 AMC motor, T18 transmission. Custom made stainless steel roll cage. This is a diamond in the rough. $4,000.00 (208) 495-1221"

http://boise.craigslist.org/cto/815863719.html 

 
To Top

My Build — Hood version 1

• CATEGORIES: Biscuit, Features This site contains affiliate links for which I may be compensated.

Over the past week I completed the form for the hood, applying a second coat of drywall mud to smooth the curves.  I had to create the hood because I lengthened the front clip about 4.5 inches.  Following that, I rubbed some turtle wax onto the form as a release agent.  Then, I laid 3 layers of fiberglass & resin.  Finally, I laid the hat channel I pulled from a different hood I had (which will serve two purposes — to hold the curve of the hood and provide support for the hinge).

As you can see below, the turtle wax didn't completely release well, so there will be some sanding.  Also, rather than apply the gelcoat to the surface of the form (which I figured would not release well at all), I have decided to apply it once I finish sand the hood.  Finally, I have done an initial trim on the hood and it fits well, but not perfect.   It will take some additional trimming, patching and sanding to finish this, but it should do fine for a first hood (much better than the first hood on my first jeep).

Continue reading

 
To Top

1951 CJ-3A Oceanside, Ca eBay

• CATEGORIES: CJ-3A, GPW (Ford MB), MB This site contains affiliate links for which I may be compensated.

The seller states $12000 was spent on the restoration of this CJ-3A and that it will now go easily down Cali highways at 80mph. My response would be, for starters, how does the hood stay down at 80mph, because there is only a hood latch on the passenger side fender (none on driver side) and no latch receptacles on the hood.  There's no mention of the MB body on this CJ-3A. The rear lights are missing on the driver's side.  Rather than a CJ-3A, the grille appears to be a slat grille in the front (probably the most valuable part of this jeep).  Caveat Emptor.

"4 wheel disk brakes, rancho suspension, 10,000 lb warn winch, power steering, power brakes, newer Ford 250 6 cylinder motor, new tires, new wheels, ground up restoration, new interior.  This old jeep has been lovingly professionally restored to better than new condition.  I had power disk brakes, power steering, Ford 250 motor, and rancho suspension added recently.  I also had the interior completely redone for $2200 with commercial grade heavy duty vinyl and super heavy duty rubber on the floors.  I also had the jeep painted with a $5500 base coat clear coat paint job which looks fantastic.  There's over $12,000 in restoration and now I've decided to sell it…."

View the pics on eBay 

 
To Top

1961 DJ-3A Springfield, MO *SOLD**

• CATEGORIES: DJ-3A This site contains affiliate links for which I may be compensated.

UPDATE: Was $1800. **SOLD**

“I have a 1961 willys DJ3a that has military running gear. The body is in very good shape and the flat head 4 runs extremely well. Has very good oil pressure, does not smoke, drives very good for a 61 willys. The body is sanded down because i was going to paint it to get rid of the cheesy camo paint job that was on it. I have 150 dollars of slate grey metallic paint primer, and reducer and what not that will go with the willys for the right price. Please call and make an offer i am a very motivated seller, I need to get the jeep out of my buddies barn. “

 
To Top

1949 CJ-3A San Diego, Ca $1400 obo

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

This is a jigsaw puzzle.  Looks like plenty of pieces with no obvious dents or rust.

"I'M SELLING MY JEEP WILLYS THAT I BOUGHT A COUPLE MONTHS AGO I WAS PLANNING TO CONVERTED TO A V8 BUT I DON'T HAVE TIME ANYMORE BECAUSE I'M GOING BACK TO SCHOOL. THE JEEP IS PART OUT BUT I HAVE ALL THE PIECES TO PUT IT BACK TOGETHER. THE FRAME HAS A 3 INCH LIFT KIT WITH NEW SHACKLES IN THE FRONT AND NEW SHOCKS,THE TUB HAVE SOME RUST ON THE PASSENGER SIDE FLOOR, I HAVE THE 2 FENDERS AND 2 HOODS FOR IT …. $1400 OBO 619 266 0886"

http://sandiego.craigslist.org/csd/cto/814330206.html 

 
To Top

1950 CJ-3A Colorado Springs, Co

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

This might be a pretty good deal.  

"This is a 1950 Jeep Willys CJ-3A. For the year, it's in great condition. It comes with a brand new, single barrel carbuerator. Nothing is missing from it, except the PTO I removed off the back. It has a 4 cylinder flathead. The engine turns over, but the new carb hasn't been hooked up yet and there's no battery so it deosn't run. I took this on as a project, but just won't have the time to put into it. It'll make a fun project for someone. Asking $2,750, but I'll consider offers. Email or call me at 303-718-0698."

http://cosprings.craigslist.org/cto/805561281.html 

 
To Top

1962 CJ-3B Portland, Or $6000

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

There's been some mods to this one, more than described by the seller.  Looks like a great trail jeep.

"RARE FIND! Relocation forces sale of Jeep! Original body, new rolling chaise, tires, custom roll cage, 5pt harness seats, 20 gal fuel cell. Custom made cover for outstide storage (has been garaged). Runs great and ready for off roading! More photos available upon request. Seller will entertain all offers and call with any questions. More pictures can be emailed. 503-314-6806"

http://portland.craigslist.org/wsc/cto/809910627.html 

 
To Top

1958 CJ-3A Rathdrum, Id $2500

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

The price of this CJ-3A sounds about right.  Some pics of this one would be nice to see.  Obviously, the year isn't quite right, but maybe it's on a later model frame?

"Willy's CJ3A, Stock, V6, Straight Body, Warn Over Drive & Bikini Top. Serious Buyer's Only Please. E-mail for More Info."

http://spokane.craigslist.org/car/777057087.html 

 
To Top

1953 CJ-5 Montana $650

• CATEGORIES: CJ5 This site contains affiliate links for which I may be compensated.

This is one of the stranger CJ-5s I've ever seen.  While the cage won't be sold with the jeep, it's not exactly a good advertisement for the kind of custom cage they are offering to make.  You gotta see all the pics to really appreciate this one.

"1953 Willys ready to finish your way or we can custom build to specs. We have various axels, motors, transfer cases, and trannys. Cage inside and rims do not go with rig. We can also custom build bumpers, tire carriers, cages, sliders to your original design. Or take it as it sits and restore. Tubs is in great shape no major rust. make offer. 406-887-2858"

http://montana.craigslist.org/cto/812578816.html 

 
To Top

MB & M-38 Parts McCall, Idaho

• CATEGORIES: GPW (Ford MB), M-38, MB This site contains affiliate links for which I may be compensated.

Here's a few MB parts:

Front & Rear Differentials DANA 25
Transmission & Transfer Case T18 (military versions)
All for $100 (all good for parts only)

M-38:

Rare fording kit for M38 – Never installed –
$225 Call for details: (208) 741-9304 

http://boise.craigslist.org/pts/808629316.html 

 
To Top

1952 m-38 Melba, Idaho $9000

• CATEGORIES: M-38 This site contains affiliate links for which I may be compensated.

I don't see anything that shouldn't be there.  Looks in great shape.

"1952 Willys M38 Army Jeep. Korean War jeep, completely restored original. New motor, tranny, Koker tires, brakes, soft top with doors. New paint, looks and runs great. 50 miles on new motor. Call Dan at 989-6333."

http://boise.craigslist.org/cto/810706424.html 

 
To Top

Old School Baja Fiberglass Seats Spokane, Wa $30 obo

• CATEGORIES: Body Parts This site contains affiliate links for which I may be compensated.

I haven't seen these type of seats in years.

"Baja fiberglass bucket seats with covers(covers are worn as you can see from pictures).Come with brackets that are adjustable.Came out of a CJ Jeep.$30obo.email or call 939-4910.Thanks."

http://spokane.craigslist.org/pts/803854687.html 

 
To Top

1964 CJ-3B Scotts Valley, Ca $3000

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

I love Scotts Valley .. I worked out of the old Borland Building for 3 years.  There are few better places in the US to work than the old Borland Building (now the Enterprise Technology Center).  As for the jeep, it's priced a bit high for a non-running CJ with significant rust.

"All original 1964 Willys CJ-3B (original matching serial number engine and chassis with number plate. Original body color was Spruce Green, now is painted a light blue color. Runs fine, but smokes a little (engine should be rebuilt eventually). Needs some minor work to get running again (battery recharged, gas lines and gas tank drained). Hood looks like it has been replaced at some point. Aftermarket heater installed in front passenger side. Rear bench seat is missing. CD ignition system installed."

http://sfbay.craigslist.org/scz/cto/806864236.html 

 
To Top

R10H-1 Overdrive Portland, Or $85

• CATEGORIES: OD Borg Warner/Rancho This site contains affiliate links for which I may be compensated.

I’m not positive, but I believe this version of the Borg Warner Overdrive can be used by a variety of 50’s and 60’s vehicles including jeeps with the dana 18 transfercase.  Here’s an article that explores the overdrive issue on older jeeps.

“R10H-1 overdrive, Warner Gear Div., believe out of 50’s chevy? Good condition! $85 or trade for willys, cj parts.”

http://portland.craigslist.org/wsc/pts/846290149.html

 
To Top

1948 CJ-2A Sonoma, Ca $1600

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

Get out your welder.  This might be a decent deal depending on how good the condition of the body is.

"Runs. 1000 miles on rebuilt engine. 12 volt system. Recent frame crack requires more skill than I have. Great project car. Call Matt for more information (cell) 707-290-1611"

http://sfbay.craigslist.org/nby/cto/803916703.html 

 
To Top

1950 CJ-3A Crystal, Mn eBay

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

This fiberglass tub flatfender looks pretty good.

“You are looking at a 1950 Willys Jeep. It has a 231 cubic inch Buick V6 which is a quite common conversion since it was used in 60’s vintage Jeeps. It has power steering, a rebuilt M18 Transfer case, rebuilt Dana 25 front differential with new Lockrite locker, rebuilt Dana 44 rear differential with new Lockrite locker, new king pin bearings, new front wheel bearings, new pinion bearing, total of $2,500 work done. Less than 100 miles since work was done. Has exceptionally sturdy fiberglass tub. Original steel hood and windshield. Larger gas tank relocated to rear. New 31″ tires. New rebuilt Holly carb, the leaf springs are new and are longer than stock for a better ride and more articulation.”