UPDATE: **SOLD** Was $1800.
(11/24/2010) Doesn’t run.
“1947 Willys Jeep,4×4,original 4 cyl.,3 speed,rare hardtop,needs restored,hasn’t ran in a while,these Jeeps are getting real hard to find.$1,800”
UPDATE: **SOLD** Was $1800.
(11/24/2010) Doesn’t run.
“1947 Willys Jeep,4×4,original 4 cyl.,3 speed,rare hardtop,needs restored,hasn’t ran in a while,these Jeeps are getting real hard to find.$1,800”
UPDATE: Still Available
(12/22/2010) This has some updates.
“1948 Willy’s Jeep, 4X4, 289 Motor, 3 Speed Transmision, Full Floating Rear End, 538 Gears, Lockers Front and Rear, Tara Low Transfer Case, Beard Seats, Rhino Lined inside, New Paint, 6000 lb. Warn Winch, Extra Parts. Runs Perfect. $8500.00 Call Sam 928-533-2940”
UPDATE: Price bumped to $2000
(12/20/2010) “1947 willys jeep V 6 motor 12volt system runs drives needs tlc call”
I’ll be taking the next two nights off. See you next year on the 2nd! Happy New Year!
Over the past year and a half Chris (from Mossy Rock, Wa) and I have been trading emails every-so-often as he works his way through his flat fender project. He recently figured out how to work with some bondo; he also tried his hand at using Herculiner. You can see the results below. It’s a bit of a trial and error process for him, but he’s making good progress.
January 1st is his birthday, so have a great birthday Chris and keep the pics coming!
Maggie mentioned to me that she was searching for a Jerry Can Tool Box someone built and displayed on line. With a little searching we tracked it down to Jeepforum.com. I’ve included two pics of it below. You can see all the pics here.
Hog forwarded this auction. Bidding just ended on this CJ-5 previously owned by Bing Crosby, reaching a high of $5850. I suspect it will be back on eBay at some point.
“Barn stored since 1973. Perfect running condition. Originally used on Rising River Ranch by the Crosby Cattle Co. Owned by Bing Crosby from new until 1973. All original, but seats and turn signal assembly. As you can see in the pictures the cosmetics are not perfect, but are easily fixed. This thing could climb a wall! She’s ready to go and up to date on all paperwork. Pink slip in hand.”
UPDATE: An eWillys reader bought all the parts.
Ken’s located here in Boise and has a variety of parts for sale and wants them gone!
Complete Fiberglass tub and front clip
Complete 304 Engine W/ Headers, Eldelbrock 4BBL, Mallory Distributor, Aluminium Valve Covers,Flywheel & Clutch.
Radiator
2 Wiring Harness, 1stock, 1aftermarket
Prothane body mount kit, motor mounts, trans mount, complete suspension and steering boot kit, shock boots. (N.I.B.)
Steering Column, Grant steering wheel, Power Steering Gear, Sector shaft.
Heater Assembly (stock)
2 Dashes, 1 with instruments and Cables, The other is painted to match tub
Seat Risers, Driver and Passenger
Front and rear seats (YJ)
1 set new springs
New spring mounts and shackles (full set for front and back)
Spicer 20 T/Case
2 T150 3 speed transmissions in near perfect condition
Roll Bar (stock)
Stainless hard line kit (brake and fuel)
Gas Tank (N.I.B. polyurathane)
Clutch and Brake peddle assy.
Console
Stainless steps
NO FRAME OR AXLES
Here are a variety of pics:
Click below to see more pics ….
UPDATE: **SOLD** Was on $500
This includes a rebuilt engine, though it isn’t installed.
“1966 Jeep with aftermarket solid top, standard on column, 4×4, 4 cylinder, with 6′ MANUAL angle, hydraulic lift plow. This is a project Jeep, does NOT currently run. Needs work, Engine re-built but NOT installed, Needs starter, alternator, battery, etc… to run. This is a cool little Jeep that would make a great winter project.”
There might be some value in this project.
“1964 Jeep CJ5, 4 X 4, manual transmission, 4 cylinder, all original. This jeep was sitting for a while and will need some work to get it running. I am firm in the $1,000 price, dont call if you want it cheaper than that. 786-556-3668”