UPDATE: Price dropped to $4500.
(10/28/2019) This could be a good price.
https://www.facebook.com/marketplace/item/363739777715397/
“327 with Muncie tranny, has full top with heater, moving and must sell”
UPDATE: Price dropped to $4500.
(10/28/2019) This could be a good price.
https://www.facebook.com/marketplace/item/363739777715397/
“327 with Muncie tranny, has full top with heater, moving and must sell”
Its a project or parts.
https://www.facebook.com/marketplace/item/1153940558144374/
“55 willys Toyota axles all new brakes, new shocks, steel rims, frame rhino lined and underside of the jeep is also rhino lined T 90 trans and dana 18 transfer 2000 obo”
UPDATE: Bobcat hood is sold.
Lots of work left on this project.
https://portland.craigslist.org/clk/pts/d/gig-harbor-now-parting-outjeep-willys/7023118105.html
“Jeep Willy’s cj3a project buggy. Tube chassis. Stainless steel grill, fiberglass hood, cj3a windshield, fresh rebuild by rears and gears on T18 tranny, Dana 20 transfer case, Dana 44 front 4.88 with Detroit locker and disc brakes, rear is a full float high pinion Dana 44 4.88 Detroit locker. New 35×12.5×15 pit bull rockers on 15×10 wheels. 4 new ORI stx 14” struts, 10 Summit Machine Large rod ends. Just lost interest in project. 6,500$ OBO for all thanks for looking.
ORI STRUTS NEW IN BOX. 3,000$ OBO
TIRES AND WHEELS, 1,600$ OBO
FRONT AND REAR DANA 44’s selling as set only. 2,500$ OBO
T18 with dana 20 transfer case 800$ OBO
any other parts make offer”
UPDATE: **SOLD** $2000
“1952 Willys CJ3A Auburn Jeep-a-Trench Trencher Jeep.
Project – must sell to save this iron. I will consider fair offers. Early Auburn Trencher wheel drive, on a 1952 Willys CJ3A.
No Title. Low miles. NE Ohio. Akron / Canton Area. This Trencher was used to dig irrigation ditches on a golf course in Northern Ohio. It was sitting outdoors when I saved it.
Frame is in great shape. Leaf springs are ok. Body is pretty good (my opinion), No filler. Could use new front floor of course. Half cab top bows – no canvas, no door frames, Monarch Governor with handle and cable. Motor and Transmission are locked, I disconnected the drive shaft to roll it. I removed all brake drums also, found one rear hub was cracked so I replaced both rears hubs. Green narrow 16″ jeep wheels go with it, see last picture.”
May be rough.
https://huntsville.craigslist.org/pts/d/falkville-two-willys/7018214475.html
“The black one is a 1949 and is supposed to run it is $2000. The other is a 1947 Willys, no motor $1200. Both need complete restoration.”
UPDATE Price dropped to $650.
Not much value here.
https://harrisburg.craigslist.org/cto/d/carlisle-willys-jeep-1955/7019185827.html
“Willy’s Jeep 1955 Antique. Great rebuild project, non-running.”
UPDATE: **SOLD** Was $2000.
(10/17/2019) Has a pto winch. Body will need work.
“I have a CJ3a That actually runs. The body needs replacing. I put a few brake lines on it and got the brakes working. It has a cheesy electrical fuel pump currently but it will crank up run drive a stop. I haven’t cranked it up since july. The Pto winch has all the parts. This is a good project jeep that needs fully restoring. I do have a clean title.”
UPDATE: Status Unknown. Was $6500.
The seller has provided a very complete description. Includes an overdrive.
“I am selling my used driver quality Willys Jeep CJ-3A. This is a great “drive-it-like-it-is” rig. Starts, runs, drives, and stops exactly as it should; even the parking brake works (could use some adjustment though to hold on a hill…). It’s not perfect, won’t win any concours, but a solid driver. Most of the work you usually have to do when you drag home an old jeep has been done. It’s been driven on the road as well having seen off-roading adventures at the NH Trail Ride and Rausch Creek PA. Used but not abused as they say. Tough to find solid non-rotted originals like this in New England. I can be tough to get a hold of on the phone based on my work schedule so texts and emails are preferred.
The Saturn overdrive allows easy cruising speeds of 55 mph (or better?). The original 3A motor was pulled previously and replaced with a fresher MB motor out of a genset. Continue reading
Interesting oil filter bracket mounting idea. Perhaps it will hold up better than the stock setup, which sometimes cracks (I’ve had two of the stock ones crack).
https://sanantonio.craigslist.org/pts/d/pearsall-willys-jeep-cj2a-parts/7020701323.html
“Two parts jeeps. Will sell as a package or individual parts. Please inquire if you have questions about a specific part, chances are I have it.”
It may be a mix of 3A and M-38 parts.
https://portland.craigslist.org/clk/cto/d/camas-1947-jeep-willy/7019566348.html
“1947 Jeep Willy Project”