To Top

1953 CJ-3B Longview, WA **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $5000

Its a project with a variety of new parts.

1953 Willys CJ3B High Hood Jeep. This is a non running project with a pile on new and rebuilt parts. The Jeep is from Eastern Washington so there is NO rust.
NEW UNUSED PARTS; Flaming River tilt column w/shaft/ujoints, Wilwood swinging pedels with master cyls., Corbeau lowback front buckets and rear bench, two windshield wiper assemblies, all window frame/windshield seals, stainless latches-hood and windshield, fuel tank w/ sender/cap/straps/, Edelbrock elect. choke carburator, Edelbrock Performer intake, Edelbrock air cleaner, Billet rocker covers, Hooker block hugger wrapped headers, Griffin aluminum radiator w/duel elect. fans (cools up to 600hp), Painless wire harness, clutch hydraulic slave cyl., Rancho 4″springs (front and rear) w/shackle reversal, Willys tailgate, Willys hood, windshield frame w/glass.
REBUILT; 1965 Chevrolet 325hp 327 (Chevelle), Dana 25 and 27 axles, 10″ drum brakes, Toploader transmission w/Hurst linkage (new clutch).
The Jeep currently has; American Racing wheels with 32″BFG all terrains (90%), all factory seats and frames, full cage, installed power steering box with pump, and also comes with an extra T10 4speed with Advance Adaptor for a Dana 18 or 20, a clean title with collector plates. I’m sure I am missing some stuff. $5000 OBO/part trade for Banshee or Toyota 4×4.”

1953-cj3b-longview-wa21 1953-cj3b-longview-wa22

[fb_button]
 
To Top

2 MBs? Vancouver, WA $2500

• CATEGORIES: MB This site contains affiliate links for which I may be compensated.

No pics provided.

42 Willies flat fender . Rolling chassis with 283 v-8, 3 speed transmission, Dana 20 transfer case,Dana 27 front end and Dana 44 rear end.Tub has new interior rear fenders. has roll bar,new after market heater, high back seats with covers top and doors. out side body needs bondoed and painted. Needs to be rewired and put together.44 ford flat fender with almost all new sheet metal inside and out. Has a cj5 frame with a spring over and reverse shackle No motor , tyranny, or transfer case. Has top and doors , roll bar. I was going to put every thing into the 44 but due to the economy I have to sell. I have allot more than 2500 into them, my loss is your gain. call”

http://portland.craigslist.org/clk/pts/4647208899.html

[fb_button]
 
To Top

Koenig Model 58 PTO Fort Morgan, CO **SOLD**

• CATEGORIES: Parts This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was on eBay.

“Up for bids is a pretty rare Koenig Model 58 PTO that came off of a Dana 18 transfer case on a CJ. This PTO originally had dual shifters to control the front and rear outputs on it, and has been converted to be operated with a pair of cables. I do not have the shifters for it, but should be easy to fabricate, or find a set for it if you want to go that route. We bought this to install onto our Willys wagon, but after more research, this PTO is at a greater angle drop and was originally made for the CJ5. The outputs work like they are supposed to when turned by hand and shift each lever by hand.”

koenig-58-pto

[fb_button]
 
To Top

1948 CJ-2A Body and Frame Moses Lake, WA **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $650.

Body and frame only.

I have a 1948 cj2a willys body and frame frame is rough set up for v8 the front half of the fram is boxed in. The body is in pretty decent condition has some rust call or text for more info or pics”

1948-cj2a-body-frame-moseslake

[fb_button]
 
To Top

1947 CJ-2A Meridian, ID **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD* Was $1000

(07/06/2014) A project.

I have a 47 jeep with title, the tub needs floors and is dented and rusty in spots. I found it on a ranch out by Ontario, it had been sitting since the 90’s. The engine turns over and holds compression but at the time it didnt have a carb so I didnt start it. I was going to just make a 4×4 that I could drive around, nothing fancy. I will part it out as it is complete, the front sheet metal is included with the sale as is the windshield. I removed them to facilitate and engine swap with a 4.3L Chevrolet. 

Here is what the full price gets you

Matching chrome rims with 32X12.50 tires
SM465 4 speed transmission
NP205 transfer case
Complete willys Jeep
Ford Ranger Radiator
Dual Electric Fans
130 Amp Ford Alternator
Massive Bumper Thing
Seat
Pull Bar
Chevy steering column with key”

1947-cj2a-meridian-id

[fb_button]
 
To Top

1949 CJ-3A Socastee, SC $2000

• CATEGORIES: CJ-3A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Still Available

(03/19/2014) This has an interesting top. Jeep needs work.

“Runs good…New back right tire, new points ,cap, rotor, wires plugs. New front drivers seat and upper radiator hose. All gauges work expect for the speedo and gas. lights work, heater blows, Hard top fabricated in 87′. Interior is good some rust on passenger floor. Needs gas tank (have outboard motor tank hooked up to it now), needs a brake job,(I have new master cylinder). Body’s fair but needs work. Windshield has small crack on the upper right passenger side … $2000.00”

http://wilmington.craigslist.org/cto/4645908049.html

1949-cj3a-socastee-sc4 1949-cj3a-socastee-sc1 1949-cj3a-socastee-sc2 1949-cj3a-socastee-sc3

[fb_button]