That’s a different look.
“1948 Jeep Willys with a 1969 350 Corvette motor with cam shaft and valve springs. New carburetor. Sitting on a 1985 C-10 Chevy truck frame, lowered 3″. New tires. ”
That’s a different look.
“1948 Jeep Willys with a 1969 350 Corvette motor with cam shaft and valve springs. New carburetor. Sitting on a 1985 C-10 Chevy truck frame, lowered 3″. New tires. ”
UPDATE: **SOLD** Was $13,900.
Could use some more photo from additional angles.
“This is a 1944 GPW Ford made WW2 Jeep with clean title. I fully rebuilt this jeep in 2012 with a frame off restoration.
The engine, clutch and transmission have been professionally rebuilt. 4×4 works perfectly. I have over 400 documented hours into the restoration, and I’ve spent 1/3 more than the asking price. its had over 1200 trouble free miles since its restoration.
This restoration uses the original tub, frame, parts and sheet metal. Reproduction parts have been kept to a minimum but include hat channels and a little sheet metal. It has all of the original Ford WW2 engine and drivetrain, axles, driveshafts, etc.
The good: runs and drives great, new Vintage Wiring of Maine correct looking wiring harness, new brakes and master cylinder, and new tires. It has reproduction data plates. Has reproduction WW2 combat wheels including spare. Has a WW2 fuel can and water bag, included.
Continue reading
UPDATE: Still Available.
(11/19/2017) Interesting build.
“TheSurf Shop,, A very unique tribute to a west coast surf/shop truck ,started life in Santa Cruz Ca. Second owner moved to Oregon, started project in 02′ , I purchased it in 2012 ,, finished her winter 14′ Drivline; 350 Gm crate Holley,hei ign. 700r-4 trans. Gm 10 bolt 3;73’s stereo,gps,volt,, oil,water,power disc. Drum.All lights led,halogen,switched fan,back-up lamps ,combination ignition switch ( no keys) . May consider $$$$$ Trades .prefer GM classics or lifted trucks??Ya never know”
Looks in good shape.
“For sale is a 1948 Willys truck that is in good shape. This truck has 60k original miles on it. ”
UPDATE: **Status Unknown** Was $10,000.
(01/012017) Looks in good shape.
“Custom 1948 Willys Jeep rat rod
Engine is a 250 6 cylinder with automatic transmission.
Custom built frame and has a Chevelle rear end.
This car is built very well and runs and drives great ”
UPDATE: **SOLD** Was $5500.
(01/20/2017) I don’t know if that engine goes in the 3A or not.
“1950 jeep cj3a nice Lil truck new body original running gear”
UPDATE: **Status Unknown** Was $3870.
Needs some work.
“Barn find Willys M38 jeep with new military tires with spare.12 volt system. Runs good, needs carb cleaned, will idle with choke on. Shifts fine. No brakes or lights. Has a winch on front, not sure if it works. Has bumps and bruises, little rust. not bad though. Have glass for windshield. No title, just bill of sale. Dont need help selling.”
Not a whole lot of value here.
“I have a ’46 Willy’s CJ2A with out a motor. The front fenders, hood,and grill are good.
The tub is toast.
Transmission, transfer case, drive line is all there and in fair to good shape.”
Steve spotted this one.
“1854 Willy Jeep front clip…. $500”
UPDATE: **SOLD** Was $3000.
(11/10/2016) “Might consider trading off my 54 CJ3B. I’m not desperate to get rid of it, just testing the waters.
Front lockers
Rebuilt motor (F-134)
Current registration
Clean title
New brakes
Heater recored
Not much rust
Gas tank rust treated and sealed.
Front tow bar
Rear set up for towing.
5.38 gearing
Running driving project.
Leak at exhaust manifold
Will need tires soon.
Leaky rear axle seal (might fix soon)
It has its ups and downs but keep in mind it is from 1954. No, it won’t do 60 mph.
Considering trading for a bigger 4×4. (Or even a Jeep with a top!)”
Jason Potts, out of Burnettsville, Indiana, shared a couple photos of his Willys Dually project, so I asked him where he found his adapters and how he got into jeeps.
Of the truck adapters he wrote, “The adapters came from Hank himself. With the original bed rusting out on me, I bought the flatbed knowing someday the original would go bad. I had a local welder cut the length of the bed down 22 inches. The black locust was cut out of my family’s woods and milled at a relatives mill. I live in an apartment and the truck is currently stored in an enclosed metal barn and will see a garage again in the spring to continue work. The motor is a 232 out of a 70’s CJ and is being rebuilt.”
Then he shared his jeep history. “Originally my dad bought a 63 Cj5 at an implement auction and we used it to get around on county roads for fishing, hunting, and for other adventures. I was in my early teens at the time. In the early spring of 2004 (Junior in high school) a culvert washed out down the road from our house forcing myself and my dad to find alternate ways to work and school. His route took him past a place that had the 54 Willys and knowing I wanted a truck he told me about it. I bought the truck for $1500 and had to buy an electrical kit for it as its wires were all the same color and no lights worked. After about 2 months it became road legal and I started driving it to school.
Senior year of high school I was still driving it. Ever since owning it, the truck always smoked and was burning through oil at such a fast rate I eventually had to put the hottest burning spark plugs and plug extensions on just to keep up, in the end I resorted to using used tractor oil. The truck got 27 miles to the quart of oil. For a long distance football game I burned through 9 quarts of oil and $27 in gas.
Through the years since I have owned/or still own a 92 Jeep Cherokee, 66 Cj5, 75 Cj5, and a 95 Wrangler. Not to be outdone my older and little brothers also bought Jeeps. Older brother bought an 88 Wrangler and little brother has bought 2 Cherokee Country’s (both were previously rolled and used as trail rigs), a 47 Cj2A and a 65 CJ5.”
Shawn McKeown wrote an article about the Our Gang Colorado Ice Racers and interviewed their president, Lisa Lannerd.