Yearly Archives: 2010

To Top

1946 CJ-2A San Diego, CA **SOLD**

April 3, 2010 • CATEGORIES: CJ-2A • TAGS: . This site contains affiliate links for which I may be compensated.
1

UPDATE: **SOLD** Was $4246

(03/14/2010) This may be a good price for a nice Jeep with some unusual history.

“4wd FANS THIS IS THE ONE FOR YOU, OWN A PIECE OF HISTORY. FORMALLY FEATURED AS 4X4 OF THE YEAR BY FOUR WHEELER MAGAZINE. TOO MUCH TO LIST CALL OR E-MIAL FOR MORE INFO OR PICS (619) 962-8170.  MATICULOUSLY MAINTAINED RUST FREE AND SERVICED ALL FRESH FILTERS AND FLUIDS. FRESH F-134 ENGINE, FRESH DANA AXELS, FRESH PAINT, NEW 31″ TIRES (NOT ORIGINAL WILL INCLUDE ORIGINAL RIMS AND TIRES IF WANTED+ $$),  GAS CANS, WARN LOCKING HUBS, CHROME RIMS, FRESH T-90 TRANS, CLEAN PAINT, CHROME, YOU NAME IT THIS IS A MONSTER.  WILL CRUISE AT 60MPH ON FREEWAY AND WILL CLIMB A WALL….AGAIN TO MUCH TO LIST.”

[fb_button]
 
To Top

1942 MB El Dorado, CA **SOLD**

April 3, 2010 • CATEGORIES: MB This site contains affiliate links for which I may be compensated.
4

UPDATE: **SOLD** Was $5000.

(03/14/2010) “Last driven in 1987, needs brake repairs and fluids, will start and run email for more information and pictures. Price is negotiable”







[fb_button]
 
To Top

Wanted: A reader looking for a solid wagon

April 2, 2010 • CATEGORIES: wanted This site contains affiliate links for which I may be compensated.
2

A reader from Memphis is looking for a wagon (not a panel) with an updated drive train, but is otherwise stock and well maintained.

If you have something like this, let me know (or comment below).

[fb_button]
 
To Top

1967 CJ-5 Tuxedo Park IV Cedar Hills, Ut **SOLD**

April 2, 2010 • CATEGORIES: CJ5 This site contains affiliate links for which I may be compensated.
0

UPDATE: **SOLD** Was $1999.

“I am selling this very rare 1967 jeep cj5A tuxedo park Mark IV project. Just rebuilt original Buick 225 Dauntless v6 engine, t86 trans and Dana 18 transfercase with FACTORY warn Overdrive. Worth more than this is parts, but this is ONE OF 89 built in 1967. More rare than shelby gt500, GT 350, and 1967 Z28….:) Anyhow, think the throwout bearing was installed wrong, and so it grinds when push in the clutch, I put it on stands and pushed through gears…does fine, so will need to pull clutch and put back together. Runs good though….BUT needs a full restoration.Not even 10 miles on engine rebuild. Not much rust, but welded on bumpers, and at some point the windshield frame was replaced with good glass from another jeep. I have no idea what year or modelof winshield frame. Brakes need replacing, in place but need rebuilt. I put coat of flat green on to get by till someone restores it. New plugs and dist cap as well. Have clear title in hand. Will need trailer. Call or email with questions.”

[fb_button]
 
To Top

1966 CJ-5 Shreveport, La **SOLD**

April 2, 2010 • CATEGORIES: CJ5 • TAGS: , . This site contains affiliate links for which I may be compensated.
0

UPDATE: **SOLD** Was on eBay.

Here’s a sharp looking CJ-5.

“1966 Jeep Willys CJ5 Totally Restored, Hard to find in this condition. Must Have!”

[fb_button]
 
To Top

1946 VEC CJ-2A Rockport, TX **SOLD**

April 2, 2010 • CATEGORIES: CJ-2A, trailer • TAGS: . This site contains affiliate links for which I may be compensated.
1

UPDATE:  **SOLD** Was $3750.

(12/03/09) It’s a bit beat up, but it’s got indents.  It doesn’t have a column shift.  It includes a trailer not shown.

“Vintage Willys in good running condition. This Willys has been used at a ranch in the Texas Hill Country (warehouse stored) for the past several years. I am selling the ranch, so the Jeep is available. NO Title. This is a RANCH jeep….has not been driven on city streets in several years. Also available is a custom made trailer to haul this vehicle (additional $750 for the trailer). Trailer has valid TX license plate. The Jeep has been converted to 12 volt, has a recent starter, almost new tires, plus many more features.”

1946_cj2a_rockport1

1946_cj2a_rockport2

[fb_button]
 
To Top

1948 CJ-2A Pasadena, Md **SOLD**

April 2, 2010 • CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.
7

This was available for a few hours and is already sold, again, after the first buyer backed out!

Dave spotted this deal.  It looks like a good price.  It has an OD, Rear Posi, nice older-style top and more.

“WillysJeep CJ2-A Rebuilt 5 years or 5,000miles ago. Needs reworked. $1500.00 firm,
NO Lowballers. No Tire Kickers, No Lifetime warranty, Will Not deliver, I do not ship, Serious inquiries only. Great project or hobbie, all parts are there and mostly original, Flat head 4 cyl., Overdrive, Posi Rear in back, No snow too deep. First one with cash or certified check takes it home. Have all recipts where I rebuilt it earlier, even have manual for you to fix by, Extra parts in back. Does run and drive.”

http://baltimore.craigslist.org/cto/1673717624.html

[fb_button]
 
To Top

I bought myself some heads — and met Greg Berheim

April 1, 2010 • CATEGORIES: News This site contains affiliate links for which I may be compensated.
0

Good News!  I found myself a set of professionally rebuilt heads for a great price (thanks Greg!).  Greg Berheim dropped me a line after I posted my craigslist Ad (wanted: engine heads).  He wrote that he had acquired a set of heads as part of an engine/parts buyout and didn’t have any use for them.

So, I drove over and met with Greg.  It turns out, Greg operates the Berheim Engine Machine Shop, a local engine shop in Meridian (208-870-1464), Idaho.  This information was especially interesting to me as Bob’s Mechanical had been bought out and most of the services moved about an hour away from me.

So, after spending time with Greg and him generously providing some advice and thoughts on my engine issues, I now know who to turn to if I need any additional work done (which I really hope I don’t need soon!!).  So, if you are in the Boise area and need some engine work done, check out Greg.

Tonight, I pulled the passenger-side head and will get the covers and intake cleaned up tomorrow.  I also carefully cleaned the surface of the heads, as the block facing surfaces had some light surface residue that needed to be removed. Saturday, I’ll put everything together and see if everything works!

[fb_button]