To Top

Sears Allstate 161 Engine San Diego, CA **SOLD**

• CATEGORIES: Engine This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1000.

Not many 161s around, let alone Sears Allstate versions. Aren’t these identical to the Willys 161s?

“Yes, Sears Roebuck & Co. actually sold cars during the 1952-53 model years, and this is the larger six cylinder 161 cubic inch flathead engine that came in the higher end “Series 6” versions. Only 2,363 Allstates were sold in two years, the cars were actually rebadged Henry J sedans manufactured by Kaiser/Fraser/Willys, as were the four and six cylinder engines they came with.

This particular engine is fairly rare and has the correct “Allstate” logo cast in the head as well as an “Allstate” tag on the engine block. It turns over and runs but really needs a rebuild. It is still standard bore, complete and has almost all the engine accessories including a good water pump, bellhousing, new clutch, two correct Carter carburetors, distributor, both manifolds, oil pump and starter. About the only thing needed to drop it in the chassis (other than a rebuild) is a generator. Most everything has been recently gone through by a mechanic.”

sears-161-engine00 sears-161-engine0 sears-161-engine1 sears-161-engine2

 

[fb_button]
 
To Top

1948 CJ-2A Hotchkiss, CO **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $5000.

“1948 CJ 2A Willy’s Jeep
Runs but needs work
original willys engine
top made to fit not original”

1948-cj2a-hotchkiss-co1 1948-cj2a-hotchkiss-co2 1948-cj2a-hotchkiss-co3

[fb_button]
 
To Top

1971 CJ-5 Sand Jeep Gilbert, AZ $7500

• CATEGORIES: CJ5, Racing This site contains affiliate links for which I may be compensated.

UPDATE: Price bump to $7500.

(09/04/2016) Looks fun.

“All the wiring is done with airplane wiring labeled
Paddle tires and rims are included.
1. 1964 Oldsmobile rear end with Henry spool and axles.
2. 1975 jeep transfer case.
3. Super T-10 4 Speed Transmission with/elite 3rd and 4th gears.
4. McCloud slipper clutch & flywheel.
5. Scatter shield bell housing.
6. 373 C.I.D small block Chevy Yencer built.
A. 400 C.I.D. Block standard bore. Block casting #3951511
B. 350 C.I.D. Billet crankshaft with Hank crank bearings.
C. Both the rod and bearings are pinned.
D. The engines been balanced.
E. Flash grounded and shotpeaned Chevy pink rods.
F. Speed pro-pistons and tapered wrist pins.
G. 14 to 1 compression W/.010 deck Clarence.
H. Chevy cast/iron turbo angle plug heads/ported and flow tested by Yancer.
I. Stainless steel 194 valves and titanium retainers.
J. SIG Errsen roler valve lifters.
K. Competition camshaft #CS-322-C-R8
L. Crane roller rockers with oversize studs.
M. The head bolts where replaced with studs.
N. Scorpion intake manifold.
O. 850 CFM dual pump Holly carburetor.
P. Mallory dual point distributor with cable tachometer.
Q. Mallory Coil and coil booster.
R. 7″ wide Mitchell aluminum rims.
S. Steel rear black rims with paddle tires. BFGoodrich trailer tires.
T. New Simpson five point harness seatbelts.
I have the original Front windshield and backseat.

I also have the pistons for 10 to 1 compression.

This Jeep does 4.6 seconds in 100 yard dash at 70 miles an hour. ”

http://phoenix.craigslist.org/evl/cto/5732033515.html

1971-cj5-sanddragger-az2 1971-cj5-sanddragger-az3 1971-cj5-sanddragger-az4

[fb_button]
 
To Top

1962 Truck JeepRod Orange County, CA $3000

• CATEGORIES: Jeep Rods, Willys Trucks This site contains affiliate links for which I may be compensated.

This has a good old-time-jalopy look to it.

“Hello all- I need to make time for other projects and have to let this one go. It’s a 62 Willys Jeep pickup. Same body from late 40s. It’s already chopped, dropped and tunneled. Lid is ready for a ragtop or a fill in. Doors shaved on exterior but interior handles still work. Not finished but not a total basket case. 230 straight 6 engine runs but needs tranny rebuilt, tires and brakes. Fun little project and not much to get ready to roll. Leave it ratty or go full out hotrod with a different grill and paint. Have pink and it IS registered non op with matching frame and body tag. Price is FIRM ( it has more than that in body work) NO TRADES.”

http://orangecounty.craigslist.org/cto/5794025380.html

truck-jeeprod-orangecounty-ca1 truck-jeeprod-orangecounty-ca2 truck-jeeprod-orangecounty-ca3 truck-jeeprod-orangecounty-ca4

[fb_button]
 
To Top

Acme Fiberglass Hardtop Tucson, AZ **SOLD**

• CATEGORIES: Parts • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $850.

This rare top looks in good shape.

“Jeep CJ5 (not CJ7), fiberglass hardtop by Acme. Fits 1976 and newer but will work with earlier CJ5 or M38A1 using a 1976 or newer windshield frame, ( I have some of these for sale). Very nice condition. Paintable to any color. $850. ”

cj5-acme-top-tucson-az1 cj5-acme-top-tucson-az2

[fb_button]
 
To Top

1956 CJ-5 Tub & Meyer’s Half Cab Nursery, TX **SOLD**

• CATEGORIES: CJ5 • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $600.

There may be value here.

“for sale is a metal Meyer half cab and doors with a CJ5 body tub. you must take tub if you want the top. and no, the frame, running gear and title are not for sale. email me your phone number for more details, condition etc.”

1956-cj5-victoria-tx

[fb_button]