Someone can use these.

https://inlandempire.craigslist.org/wto/7570127455.html

“Selling a pair of Willys MB or Ford GPW combat wheels.
These are original 40’s military wheels not reproduction
I only have 2
Asking $300”

These should be of interest to someone. Note the top left rim seems to have a flat spot at the bottom of it?

https://portland.craigslist.org/clc/wan/d/oregon-city-full-set-military-combat/7519454446.html

“Super hard to find, original military combat wheels I put this set together over the last couple of years. These are real nice. barely any rust. There are after-market wheels, so don’t settle if you are restoring!
1000.00 cash or trade for morgan silver dollars or something amphibious.”

Maury shared this ad.

View all the information on eBay

“Here we have for sale an Original 1970’s Jeep CJ7 CJ5 Renegade Factory Forged Aluminum Slotted Wheel. This is a rare and highly sought after wheel that was a factory optional wheel for CJ’s back in the day. The wheel is pretty nice and its been off a Jeep for years. The aluminum is in good shape. The lug holes are in good shape. The wheel measures 15×7. There are a couple nicks in the aluminum and around the outer lip where wheels have been stacked on top of it. It should polish up well and be ready to run again.”

UPDATE: **SOLD** Was $400.

“all 4 wheels are very good no rust  , lug holes are good ,valve stem holes are good. just have junk tires on them all 4 look just like the pics below”

This ought to interest someone.

https://allentown.craigslist.org/wto/d/emmaus-wwii-original-16-combat-wheels/7508228439.html

“$750.00 for all four. WWII original 16” combat wheels from a Ford GPW jeep, all split rim. Two tires are damaged, another worn, and the other new with some dry rotting. Lugs missing from one. No visible damage to rims other than surface rust.”

UPDATE: Lee has another set of four slot rims like the ones pictured below.

https://cosprings.craigslist.org/wto/d/pueblo-jeep-bronco-15×7-slotted/7480936710.html

“MAKE OFFER for this vintage matching set of (4) slotted aluminum 15×7’s that are 5 lug hole 5×5.5 inch bolt pattern. The 5×5.5 inch bolt pattern should fit the early and later Ford Broncos and F-100, F-150 Pick-Up Trucks. I believe that theses may also fit Jeep, Jeep CJ Renegade, Jeepster Commando, CJ5, CJ6, CJ2A, CJ3B, CJ3A, and CJ7.

Also, the lug holes look good and the center hole measures approximately 4.25 inches. 5 on 5.5 inch bolt pattern. Back spacing is 3 and 3/8ths inches.
“

These are getting hard to find.

https://portland.craigslist.org/clc/wto/d/oregon-city-15×8-steel-wheels-5×55/7475470418.html

“15×8 Steel Wheels, 4” Backspace, 5×5.5 bolt pattern.
Powder coated black back in ‘07, some rusting coming through the powder coating, will need refinished if want perfect…. Vintage wheels Came off my old GPW, fits a lot of old Jeeps, Dodge, Ford trucks as well as some Geo, Daihatsu etc. Awesome rat rod or 4×4 wheels !!”

Someone was looking for 16″ rims.

https://buffalo.craigslist.org/pts/d/mars-willys-jeep-cj2a-cj3a-wheels/7464077151.html

“I am selling a set of four Willys CJ3A (can also be used on a CJ2A) that are in excellent condition. These have been in an interior storage facility for years and have no rust or the typical pitting. I don’t see any significant areas of rust, etc. These wheels are 16″ x 4 1/2″.

These need a quick blasting and will be ready to paint. I have some older CJ2A wheels and can include a fifth wheel if you need a complete set. Please drop me a note or call if you have any questions. Open to reasonable offers, but please keep in mind that repo wheels of this era run about $180 ea.

I also have a very nice F-134 engine with T90 transmission and Dana 18 transfer case. I will be listing those in a few days.”

UPDATE: **SOLD** was $500.

Maybe somebody can use these?

“4 new (been in storage 40 years) buckshot wide mudders.8.5 wide.850 tread 32.5 tall.p78-16lt 6 p”

Blaine spotted these rims. I think there are 4(?) rims?

https://portland.craigslist.org/clc/wto/d/clackamas-rare-16×9-slotted-aluminum/7357118956.html

“Rare 16×9 slotted aluminum mags 5×5.5 … Old school 5×5.5 wide center hole aluminum slotted mags with lug nuts. I had these on my 1981 Dodge Power Ram. They will fit Jeeps, Dodge, some Fords and a few other 4 wheel drive vehicles. Center hole is 4″ for large hubs.”

Blaine found this ad. It could be a good price on Kelsey Rims.

https://ventura.craigslist.org/pts/d/ojai-jeep-parts/7334956648.html

“1967 CJ 5 parts
7- Jeep cj5 wheels 5×5.5 bolt pattern 2 with tires holding air 25 each
4- Jeep yJ wheels 5×4.5 bolt pattern with out tires
Fly wheel & clutch $75
Exhaust manifold $50
Rear end Dana 44 $175
Front Dana 27 $175”

These look like a good price.

https://www.facebook.com/marketplace/item/484457745994598

“4 – 1981 Jeep CJ7 factory aluminum wheels 15″ x 9″ – $300 for all 4”

UPDATE: **SOLD** Was $30.

If you need some cheap rims, these ought to work. Seller has a bunch of other jeep parts, but isn’t specific about what.

“Solid wagon wheels removed from the 1983 CJ seven, i’ll do a width and backspacing addition to the listing later but they’re pretty standard,I have many jeep parts please ask and I’ll check my storage I have too much crap to even remember”

UPDATE: **Sold** Was $200.

I haven’t seen turbine rims pop up for sale in a while.

“Vintage aluminum 15”x10” Western Turbine Hurricane wheels with 5×5.5” bolt pattern. These wheels fit a variety of trucks and SUVs including certain Dodge, Ford, Jeep, Kia, Mitsubishi, Willys, and other vehicles. Check your wheel hub for the 5×5.5” bolt pattern or do a GOOGLE search to check your specific application. These work and look good on both an old-school or late-model ride if you’re running a large format all-terrain or mudder tire. Asking $200 OBO for the set. Phone, text, or email me for additional information, thanks.”

Maybe someone can use these?

https://seattle.craigslist.org/see/pts/d/lynnwood-willys-jeep-repro-combat-rims/7325568073.html

“New in box reproduction MB or GPW combat rims 6 x 16 . $300 for both”

UPDATE: **SOLD** Was $150.

Looks like a good price.

“I have a set of 4 15×12 5×5.5 deep dish steel wheels with a 3.75″ backspacing for sale. They fit old ford dodge & jeep. Asking $150obo”

UPDATE: **SOLD** Was $360.

Maybe someone can use these?

“This is a set of Kelsey Hayes steelies which measure 16×4.5 and have a 5 on 5-1/2” bolt pattern. I am asking $90ea for a total of $360. The exterior face has been reconditioned. Lug holes are all in great shape along with the valve stem holes. These wheels could be found on Military Jeeps, Internationals, Willys and other vintage vehicles from the 40’s up thru the 60’s. If you are restoring a classic and need a nice set of time period correct wheels, these just may fit the bill.”

UPDATE: **SOLD** Was $150.

Maybe someone can use these?

https://www.facebook.com/marketplace/item/1580735935449264

“These are 2 turbine rims for a vehicle with a 5×5.5 bolt pattern. All rims are in good shape with no cracks. Please ask any questions thanks for looking I only have 2”

Blaine spotted these rims. I’m sure someone can use them.

https://boise.craigslist.org/wto/d/boise-kelsey-hayes-15×8-jeep-wheels/7270697563.html

“Set of 5 15×8 kelsey hayes wheels that were factory on some models of jeeps. 5×5.5″ bolt pattern.”

There are folks looking for these.

https://www.facebook.com/marketplace/item/151832063126790

“Original Equipment, needs a good cleaning. The spare is banged up. See Pictures. Made by American Racing.”