To Top

1946 CJ-2A Pollock Pines, CA **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Was $4500. **SOLD**

(10/27/09) This is a Square Finder Willys Jeep; I’m don’t know what that means?  The jeep sounds well modified.

“New Starter, New seat in back, Buckets in front, Full role cage, 1967 Chev. 327 eng., New Power Steering Pump, Radiator rodded out, 15 x 10 Chrome Spocked Rims, Tires like new 33 x 12.5 x 15, Ten Thousand Lb. Warren Winch, Rebult Tranfer Case, SM-420 Transmission, Running gear from a 1973 CJ5, Model 30 Front end, Dana 60 rear end with Possi-Traction, 427 Gear Ratio, And a newly fully rebuilt Rodchester Spread Bore Carb.

1946_cj2a_pollockpines

 
To Top

1950 CJ-3A Lincoln, Mt $5000

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

UPDATE:  Price dropped to $5000

(10/11/09) I’m not sure what’s on the hood.

“This jeep is in excellent condition. Has bucket seats, strong running four cylinder motor, three speed standard transmission and a great heater. Comes with four 600/16 studded snow tires, ice chains, and a full soft top with doors. Great winter work vehicle and tons of fun in the summer. Reasonably priced. Call 406-461-6894”

http://montana.craigslist.org/cto/1451162858.html

1950_cj3a_lincoln

 
To Top

1947 CJ-2A Pigeon Forge, Tn **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2350

“I have a 1947 jeep willys it has the 231 v6 in it and it is in great shape runs very good. it has a new master cyclinder needs to be put on. i put alot of work and time into it.”

 

1947_cj2a_pigeonforge

 
To Top

Windshield Glass Template for CJ-3A?

• CATEGORIES: News This site contains affiliate links for which I may be compensated.

UPDATE: Jim gave me some good advice on going with some ‘flat glass’ shops rather that windshield specific shops.  I’ve asked for some quotes and will provide updates on my quest.  Thanks Jim!

I need to have a windshield cut and I don’t have the old windshield glass to use as a template.  I’ve gotten one quote for about $200 to have the glass templated, cut and installed (which seems a bit high to me).  I think if I had the template, I could get the price lowered. Anyone have such a template?

Then I got to thinking, wouldn’t it be useful to have a series of windshield glass templates for a variety of jeeps in PDF form that could be downloaded and printed (probably have to printed at a Kinkos).  If anyone knows of any existing templates online, please let me know.

 
To Top

1950s CJ-3A? Kamiah, Wa Auction

• CATEGORIES: CJ-3A, Unusual This site contains affiliate links for which I may be compensated.

I’m guessing this is a  CJ-3A.  It will be going up for auction.  Those are the most unusual doors I’ve ever seen.

“To be sold at Auction. If you would like more information email tiger@tigerauctioneering.com or call 208-503-0235 and place your bid.”

http://seattle.craigslist.org/est/cto/1450543706.html

1950s_cj3a_kamiah

 
To Top

1946 CJ-2A Federal Way, Wa $3750

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1946_cj2a_federalwayNow that’s a big towbar.

1946 Willys CJ 2A • Everything stock but color, roll cage and custom bumpers  • Rebuilt 4 cyl GoDevil motor, generator, carb, radiator etc  • Rebuilt t90 transission and transf case  • New brakes and interior  • Front towbar  • White spoke wheels and street tires  • BestTop convertible top  • Currently licensed in WA state as an antique  • Runs great. I’ve owned this for over 20 years. Complete rebuild inside and out.  Done with this one. Looking for a new project. This one needs a good home for auto shows and offroading. All reasonable offers considered. Call Steve at 253-517-8747 to arrange a showing. Moving. Must sell. ”

http://seattle.craigslist.org/skc/cto/1450499909.html

 
To Top

1957 DJ-3A Lancaster, Pa $2500

• CATEGORIES: DJ-3A • TAGS: This site contains affiliate links for which I may be compensated.

I’m not sure if this runs or not, but the body looks in reasonable shape.  This is a DJ with a Tailgate.

“1957 willys jeep, Need complete restoration. The body is not too bad, very little rust. The motor needs rebuilt too. call Ryan to see 717-393-7717.”

http://lancaster.craigslist.org/ctd/1449693418.html

1957_dj3a_lancaster

 
To Top

1954 CJ-3B Huntsville, AL **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6000.

“54 Willys CJ3B. I have had considerable work done on this Jeep in order to make it a reliable hunter’s friend. The motor was professionally rebuilt by R.P.M. Cylinderhead and Engine of Fort Walton Beach, Florida and has zero miles on it. All other work was completed by Jimmy’s Motors in Fort Walton Beach Florida. Receipts available. It has: completely rebuilt engineto use unleaded fuel, new steering shaft, gear and steering wheel, new brakes, wheel cylinders, springs, etc., including new master cylinder, new shocks, new windshield and frame, new radiator, new tailgate, new hood. AND it has a brand new Warn M6000 wench, which has never been used, and was professionally installed by Accent Accessories of Fort Walton Beach Florida. I’ve owned a number of Jeeps and wanted this one to be THE Jeep, but I came down with cancer and can no longer afford to keep it. It is a 1954, but is registered as a 1948 because the DMV made a mistake when I registered it and they are apparently staffed by morons who can’t get understand this VIN is not the same as the modern 17 digit VINs.”

1954_cj3b_huntsville

 
To Top

1956 CJ-5 Mount Vernon, NH $1000

• CATEGORIES: CJ5 • TAGS: This site contains affiliate links for which I may be compensated.

It runs and has a plow.  Looks like it might be a good price.

“1956 WIlly’s in as is condition, runs great, looks ok.. we never registered this only used as a yard machine, so have no title on it, previous owner did not register either, so no old registrations for paperwork other than bill of sale. still has some original features… I am listing this for my husband and he did not give me alot of info… has original motor… we use it to plow with.. any questions please call in the evenings when he is most likely home, tho he does not work a 9-5 job, but I can get answers and get back to you.. price without plow is 800… call 603 673 1361 or email.”

http://nh.craigslist.org/cto/1449428500.html

1956_cj5_mountvernon

 
To Top

1952 M-38 & 1946 CJ-2A Bedford, NH **SOLD**

• CATEGORIES: CJ-2A, M-38 This site contains affiliate links for which I may be compensated.

1952_m38_1946_cj2a_bedfordUPDATE: **SOLD** Was $7500

Here are two jeeps for sale, but only one is pictured.

“willys jeeps 1 1952 m38 complete off boy rest near mint cond also included 1946 cj2a both go same time”

 

 
To Top

1946/47 CJ-2A Lake County, CA **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2000.

Unusual paint job.  It looks like it is mostly there. Non Running.

“registered as 47 but all serial #s have it as a 46.  All original except rims and tires. has tow bar.  original flat head 4 engine. needs rebuild does not run.  i think it is front bearings/ common with this engine, trans, transfer, steering, clutch, brakes all worked fine, body is straight minimal bondo. small rust issue on floor under seats, no more than expected after 63 years, price is firm would rather not sell but… I work for cal fire and am gone alot so, i may not reply right away be patient, I will get back to you”

1946_cj2a_lakecounty

 
To Top

Randy finds a jeep in the Grass/Sticks/Weeds

• CATEGORIES: Builds This site contains affiliate links for which I may be compensated.

Randy found this CJ-2A for a friend at a great price.  It looks in pretty good shape considering the height of the surrounding foilage.  He’ll be sending more pics.

P1000085

P1000084

P1000086

P1000087

P1000088

P1000089

 
To Top

1944 GPW Bryan, Tx **SOLD**

• CATEGORIES: GPW (Ford MB) • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6700.

This is a long, but detailed post.  I’ll show the links, the pics and then the description.

http://www.surfacezero.com/g503/showgallery.php?cat=2167&ppuser=622

1944_gpw_bryan

1944 Ford GPW WWII Jeep (Similar to Willys MB Jeep)

This was a west coast vehicle (I moved it to Texas this summer) and is fairly good in terms of rust and dents, but there is definitely work to be done. The worst part of the body is the fuel tank sump, which is totally missing. Also, there are the usual sections of the hat channels that will need addressing. There are dents in the rear floor and fender wells, though the steel is in good shape and could be straightened. Same with the rear panel. The chassis has the standard-issue bubba treatment on the front bumper gussets, which are attached to a makeshift front bumper. I think the lower gussets could be salvaged, but the uppers will need to be replaced. The left rear of the chassis has sustained damage and has had a brace welded onto it. The rear crossmember and pintel plate will need to be repaired or replaced.

Okay, so that’s the bad news. The good is that I’ve been collecting a whole bunch of parts over the past couple of years to bring this closer to being a correct restoration.

Among the components I’ve got are: one complete GPW engine and a spare block. The engine is serial number 259468 and the casting date is b28522 (February 28, 1945). This was a running motor when I bought it, but is currently not operating because I took off the Willys head that was on it and have only temporarily bolted on the correct Ford head to keep dirt out of the cylinders. I purchased that engine to transfer all the components over to a November 10, 1944 block, which is dead-on correct for an early December 1944 GPW. (The estimated DoD on this GPW is either December 11 or December 12, 1944. These dates are based on GPW 240211, which is a numbers-matching GPW located in Northern California with a DoD of 12-12-44 on its original data tags. The casting date on GPW 240211’s engine is November 11, 1944.) On the spare block I cleaned up the serial number pad and restamped the “GPW <->” in the correct font, leaving the number blank after that. (There is a cartouche on the manifold side, which identifies this as a replacement block.) I haven’t had the engine tested, but there are no apparent cracks. Three of the holes for the head bolt studs, however, are oversized and will either need to have special studs or be helicoiled. (These are the three studs that are located underneath the oil filter mounting bracket.)

I’ve also acquired a bunch of the peripherals for the engine, including an NOS Autolite GEG 5101 generator (April ’48, with a spare used February ’45 that has the correct SP 484A pulley); a GPW water pump and GPW thermostat housing; GPW exhaust and intake manifolds; a correctly dated 1944 fuel pump with primer handle; replacement tags for all the electrical components (generator, distributor, starter motor, voltage regulator); and the GPW head that I mentioned above.

In terms of the body, I put on all the script-marked grab handles and rear footrests (one footrest will need to have rust welded in the lower center section); original F-marked bumperettes; correct Stimsonite No. 12 reflectors in Guide A2 No.415 A bezels; a matched True Temper axe and shovel set; the correct Stewart-Warner gas and oil gauges; a correct block F amperes gauge; a correct King Seeley speedometer; a 1944 Gerry Can; five original combat rims; an ANCO Rainmaster tandem wiper set (NOS); an original F-script pintel hitch; a pair of NOS Hall grille marker lights; an NOS Corcoran Brown blackout driving light; original rifle rack; and much more. The driver’s seat is F marked, but the spare driver’s seat, passenger and rear seat are not. There is also a complete set of original cushions with steel springs and horsehair inserts.”

 
To Top

1949 CJ-2A Las Cruces, NM **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3995

It looks solid.

Restored /Original 49 CJ2A Willey’s. Has been long term project car I finally finished up but have moved on to other toys/challenges and can use the garage space and cash! So no trades please. Runs well, everything works. Original engine, tranny. Converted to 12 V, new engine wiring harness, fuel tank & lines, fuel pump, brake lines, master cylinder, front seats, custom roll bar, miltary tires/wheels (include side mount spare). New flat desert sand paint, interior coated with flat black bed coating. Have new canvas military top (no sides) that’s never been mounted.”

1949_cj2a_lascruces

 
To Top

Two Willys Jeeps Van Nuys, Ca $300

• CATEGORIES: CJ-2A, CJ-3A This site contains affiliate links for which I may be compensated.

These look familiar, don’t they Chris?  I could use the wipers ….

“I have these two old relics, ready to add to your yard art collection, or perhaps to help breathe life back into your other Willys Jeep project. No VIN’s, no tags, no title. For parts salvage value only. Must be towed away. One is what is left of a 1948 CJ2A, and the other is a 1951 CJ3A. One extra poly fuel tank, one has a PTO (big), one has a Buick V6, the other has the original rare Hurricane six. Trashed and tired, still cool. $300 cash money. Van Nuys location.”

http://losangeles.craigslist.org/sfv/cto/1444874230.html

2_jeeps_vannuys

 
To Top

1948 CJ-2A Santa Paula, Ca $7500

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

This has been lovingly ‘restored’; however it is missing the front running lights.

“1948 Willys Jeep. Absolutely beautiful Jeep, Refurbished and ready to drive away. Lovingly restored, and a real eye catcher. Must See it to appreciate it!! Take a look at the photos and give a call to come see…..”

http://ventura.craigslist.org/cto/1448600120.html

1948_cj2a_santapaula

 
To Top

1950 M-38 Clovis, Ca $4250

• CATEGORIES: News This site contains affiliate links for which I may be compensated.

I”m not sure what exactly needs to be done, but the price seems a little high for a project.

“PROJECT JEEP !!!!! 5 NEW PRO COMP MUDDERS 33/12.5/15 TIRES, 5 NEW STEEL BLACK WHEELS, 4 NEW RANCHO 5000 SHOCKS, NEW RANCHO SPRINGS AND SHACKLES, NEW BEST TOP SOFT TOP (still in box), SM465 TRANNY MATCHED TO A DANA 20 TRANFER CASE (both rebuilt), NEEDS MORE WORK JUST DON’T HAVE TIME OR THE DESIRE TO DO ANYMORE, ASKING $4250.00 OR BEST OFFER, TITLE IN HAND.”

http://fresno.craigslist.org/cto/1448321272.html

1950_m38_clovis

 
To Top

Wanted: 1948/1949 Jeepster Parts Wenatchee, Wa

• CATEGORIES: Jeepster This site contains affiliate links for which I may be compensated.

Here’s someone looking for Jeepster parts.

“Looking for parts for my 49 Willys Jeepster. front grille from a 48 to 49 wagon will fit as will the hood. But also need the jeepster chrome strip down the hood and the chrome T that goes on that year of the grill. 50 -51 will not work and are totally different. Also looking for interior parts and gauge cluster which is the square one. And looking for the side steps that go on the rear fenders. Would like the correct seats both front and back. And steering wheel center for black steering wheel.”

http://wenatchee.craigslist.org/pts/1448536050.html

 
To Top

1948 CJ-2A Redding, CA **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE:  **SOLD** Was $3500

The pictures are a bit far away to tell much.  It looks pretty good.

“New Upolstery, Ready for Hunting. All original convert to 12 volt.

1948_cj2a_redding3

 
To Top

1961 FC-170 Stowe, Vt $7000ish

• CATEGORIES: FC150-FC170-M677 • TAGS: This site contains affiliate links for which I may be compensated.

Gordon wrote me today and offered to provide readers with some more pics.  This looks like a very nice FC.

Gordon writes, I found the truck in Oregon (Forest Service Truck).  Have a huge book of all records during its life in the woods.  Brought it back to the East Coast, Took the bed off, Converted Transmission to a Automatic 400 turbo tranni from a full sized Blazer.Put a 350 in it.Boston Acoustics Sponsored it with a custom music system for Extreme sports events. Yakama Rack Co sponsored it as well.We used it for One winter until we parked it for 6 years.New sets, 3 Point Harness. Super Fun, She did 70mph on the Highway pulling a house!I have a clear title.Around 15K into the truck, Looking to get half the money back or a trade worth around $7K. Trade for a small jeep cj 2 or 3 Or a waterski boat either or worth around 7K.

truck1

jeep1

jeep 3

 
To Top

1964 CJ-3B Fresno, CA **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3000.

It appears in good shape.

“1964 CJ3B Jeep. 4 cylinder Cleveland engine. New brakes. Eng runs well. Rear main leaks oil. Fun project ”

1964_cj3b_fresno

 
To Top

1944 MB Paradise, CA **SOLD**

• CATEGORIES: MB This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3500.

This looks in good shape.

“1944 militry jeep willys.3.1 v/6 odd fire.custom radiator,rollbar. all the rest is original.licenced and ready to go hunting,fishing or just out for some good old fashion fun.Comes with tow bar and hooks up easlly.Has reciepts for rebuilt trans with new custom clutch and rebuilt rear end.Climbs like a goot and pulls like a train”

1944_mb_paradise

 
To Top

PNW Race Jeep Selah, WA **SOLD**

• CATEGORIES: Racing • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2000

The motor needs work, but the price still looks decent.

“1948 willy’s race jeep has a1966-77 bronco frame, motor, tranny, and running gear, 400hp 289-302, motor needs work, full cage, 5 point harness,tilt fiber glass hood and fenders, $2000 firm call (509)697-8209 ask for Tom or will trade for equal value quad. also has a12 gal fuel cell.”

1948_racejeep_selah

 
To Top

Roll Cage Draper, Ut $300

• CATEGORIES: Roll Cage This site contains affiliate links for which I may be compensated.

It’s a good price for a cage.  That front seat part looks pretty far forward though.

“I have for sale a custom built full roll cage for a Willys Jeep. This will fit the CJ2A, CJ3A, or M38. It incorporates the seat mounts for optimum safety as well. This is a very nice cage for a fraction of what it costs to build. Please call with any questions. (801) 403-8511, and ask for Kurt.”

http://saltlakecity.craigslist.org/pts/1447285995.html

rollcage_draper

 
To Top

1948 CJ-2A Denver, CO **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $4200

Last posted 02/04/09

“Nice original condition 1948 Jeep Willys. Original VIN Plate on firewall, Good title. Garage kept. Good condition. Original 4 cylinder “Go Devil” engine. Original drive line with good engine, transmission, T-case. etc… Nice Blue paint approx 10 years old. Original 6 volt system. No rust. Very good body. New windshield frame, seat frames and Beechcraft seat cushions w/ rear seat. NDT tires on 16″ wheels. Includes tow bar and rear tow hitch. I bought it 3 years ago as a project and but have not found time for it. Needs minor work to complete. Parts included but not installed include new windshield cowl, glass, insall kit; new seats, cushions, seat belts. Great father/ son project.”

 

1947_cj2a_denver