To Top

1943 Crawler Dublin, CA **SOLD**

• CATEGORIES: MB • TAGS: , , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $5500. Could this have been a Coast Guard jeep?

“1943 Willys – Currently registered and street legal in CA. Smog exempt. 4.3 liter V6 Chevy engine. TH 350 Transmission. Triple Toyota transfer cases (4.7 front, 3.8 middle & 2.8 rear). Dana 44 in the front, open, chrome molly axle shafts, ctm u-joints. Dana 60 in the rear with spool, 410 front & rear. Hummer H1 12 bolt bead locks on Good Year military radial tires. Crawls like you’ve never seen before. A MUST see/drive in person vehicle. Willing to talk about a trade. Let me know what you have to offer. Serious buyers only.”

 
To Top

1950 CJ-3A Bend, OR **SOLD**

• CATEGORIES: CJ-3A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2900

This looks solid.

“1950 willy jeep in Excellant condition. 4-cylinder Chevy Iron Duke Motor. 4×4. No rust. New tires. Runs and drives really good.”

 
To Top

1946 CJ-2A Telford, PA **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $4000

(07/22/2010) There’s a bit of a hole in the hood, but otherwise looks pretty good.

“1946 Willy’s CJ2A $5,000.00. **F-head 4 cylinder motor (not the original flat head) **Solid Rhino Lined floors, **1″ body lift, **New 29″ military tires, **New gas tank. This Jeep runs well and can be driven as is. It needs some work to be completely reliable or can be restored. The frame is solid and the floors are new. The body is usable, but showing its age. Some of the wiring is new, the starter is rebuilt, as well as the head. It has a new carburetor, new spark plugs, coil, cap, rotor, and a new battery.”

 
To Top

1946 CJ-2A North Ferrisburgh, Vt **SOLD**

• CATEGORIES: CJ-2A • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $20,995

(05/08/2010) “This Jeep went through a total body-off, fully documented professional restoration in Pennsylvania 3-years ago at a cost of over $50,000. Painted in the rare factory correct Normandy Blue makes this CJ stand out. It has been driven only 300 miles since restoration in parades and shows. An ideal addition to any collection or ready for regular use. Everything works as new. Call for more details and photos”

 
To Top

1948 CJ-2A Centralia, Wa **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

1948_cj2a_centraliaUPDATE: **SOLD** Was $2700

(07/16/2009) Given the body is new there is some real value here.

“1948 Willys Flat Fender CJ2A. Small block Chevy V-8 with Edelbrock manifold, Holley 4bbl and HEI. SM465 4 speed, AA adapter, Dana 18 T-case, Saginaw power steering, On plated and reinforced original frame and axles with a spring over. Brand new body tub, front fenders, tailgate. The new body kit was $3,000.00 alone. Willys scripted hood.  Good used Windshield.  Includes collector lisc plate and a couple boxes of spare parts including some military black-out lights and some extra beige paint. Supposedly most of the frame work was done by TC’s off road in Kent a few years back. Not my project, bought it for the new body, but decided to go 3B High Hood instead.”

 
To Top

Just a Few updates tonight …

• CATEGORIES: News This site contains affiliate links for which I may be compensated.

Just a few updates tonight.  We’ll return to more updates tomorrow (Sunday) evening …

 
To Top

Tips: Harmonic Balancers Can Go Bad on Willys Flatheads

• CATEGORIES: Tips & Tricks This site contains affiliate links for which I may be compensated.

I have received a variety of useful tidbits that Sam has been sharing with me, though either Sam or his employee Lee deserve credit.  Lee worked for many, many years in military motor pools (as did some of his family members) and now works with Sam to have some fun.

On to the tip …. One day Sam purchased and trucked a flattie to his shop with an engine that sounded problematic. In fact, he got a great deal on the jeep because both Sam and the Seller though the engine had a problem.

Now Sam, who is no stranger to engines of all types, suspected something inside the engine, but as soon as Lee heard the sound, he said it was the harmonic balancer. Sam looked at Lee and said, “really?”

Lee probably responded with something like, “you young whipper snappers don’t know anything!”  (Note that Sam and Lee are about the same age).  So, Sam proceeded to swap out the balancer with another one they had and, sure enough, within short order Sam had a perfect running flathead.

Lee told Sam that the harmonic balancers can go bad on a Willys flathead engine.  So, before you have that flathead rebuilt because it is making a noise, check out the harmonic balancer.

 
To Top

Buck Completes His Hunting Jeep

• CATEGORIES: Builds This site contains affiliate links for which I may be compensated.

There have been some outstanding eWillys reporters filing stories from all areas of world, but none were more intrepid nor braver than the Head of the eWillys Bureau in Afghanistan, Lt. Buck.  His report from the front lines (or close enough) on Willys in a field in May of 2009 from Afghanistan marked a gold standard in reporting.

The fact is, rumor has it he even joined the Army to get there, because the penny pinchers at eWillys corporate wouldn’t buy him a plane ticket.  Now that’s dedication!

I am extremely happy to report that Buck made it safely back to Montana and, I hope, has found some well deserved peace.  Since he’s been home, he managed to complete his CJ-2A build, which he put together as a vehicle to explore the central Montana plains and do some hunting.  What better use for a jeep is there than that!  Congrats and Thanks Buck!

Buck writes, “Well, I’m happy to say that I’m back home and my jeep is finally done after 10 years of on again off again work. Attached are photos of my dog Uncas and me out hunting grouse in the vast wheat fields of central Montana. I never wanted a museum piece, but a functional piece of history.

 
To Top

Photographic Tips for Craigslist, eBay

• CATEGORIES: Buying-and-Selling This site contains affiliate links for which I may be compensated.

NOTE:  Though I updated the menus above to provide access to more information, I didn’t always have content (which is why there are still a variety of dead links).  So, I am having to create the content, such as the content below, as we go along …

The tips contained herein are designed to help you take better photos for selling, though they are useful tips for general photography. As always, readers who know more about this subject (really, my knowledge bar isn’t set too high), feel free to correct or add to this information by emailing me or by adding comments!

Full disclaimer:  I don’t pretend to be a photographer with anything close to a real aptitude for the art of photography; Nor have I studied any of the science behind a good photograph.  I’ve never taken a class and never dated a photographer or even an aspiring photographer.

No, the closest I have come to being a photographer was working at Ed Firmage Jr.’s Springdale (Utah) photographic showroom where I monitored the store and tried to sell art (and he’s got some beautiful art); however, I only sold one piece during the entire summer I worked there (it was expensive stuff), spending most of my time working on websites and business plans or staring out the window at the entrance to Zion National Park (pics) (there was a tragic lack of traffic into the store, but it was a beautiful place to spend the summer!).  I never did get money out of the deal, instead I got paid with Framed prints and books, which was priceless ….

Back to our topic, the whole purpose of adding images to a Craigslist, ebay, or other online ad is to improve the marketability of your jeep (or whatever you are selling).  Making the most of images to tell the story of your jeep can only help your ability to sell it.

Because, I’ve literally reviewed thousands of jeep ads, I feel like I can provide some reasonable suggestions that will help you photograph your jeep better, whether to sell it or to take better pics.

Specifically, there are 7 areas I will briefly cover here:  1)  Use a good camera, 2) Light matters, 3) Create an overall shot, 4)  Choose a good background, 5) Other photograph suggestions, 6) Lighten or correct the shots if necessary, 7) Size and change the images so they can be uploaded correctly.

1. USE A GOOD CAMERA

I can’t make old fish taste good [a chef once made me try – but that’s a different story] and you can’t make a poor quality camera take good pics.  So, my first bit of advice is to use the best camera you have. I have two cameras, one is a 2 mega pixel camera on my phone and the other camera is a Leica 3.1 mega pixel digital still and video camera (what I call my ‘real’ camera).

Though very convenient, my phone takes dark and grainy pics, though no doubt some of the phones released in the past year do better.  So mine is great in a pinch, but when I need good pics I turn to my ‘real’ camera.

If you are asking people to spend $2000 or more dollars on your vehicle and you don’t have a decent camera, then seriously consider buying one. There are plenty of cameras you can buy for under $100 that will do a good job.  Just go here for a list of some cameras that will likely do the job (http://cameras.about.com/od/topcamerasatpricepoints/tp/Top_Cameras_Under_100.htm).

Here are 2 sets of comparison photos.  On the left side you can see pics taken with my ‘good’ camera.  On the right are pics taken with my cell phone.  I have not altered these pics at all except to shrink them for this example.

So, I believe the takeaway here is always use good fish ….

Continue reading

 
To Top

1999 ‘M-151A2 Encore’ Pompano Beach, Fl **SOLD**

• CATEGORIES: M-151 • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: Was $11,500.  **SOLD**

Bill pointed out that this is actually a M-151A2 Encore.  These were built  using the M-151A2 running gear for a couple years in the late 90s.  You can read more about them at the G503.com siteHere are good pics of another EncoreHere’s the discussion of the body at the G838.org site.  I tried to find more info on the history of Encore, but didn’t have success, though it went out of business around 1999.

Greg pointed out this unusual M-151. It’s not clear to me if this was built from scratch or rebuilt, but it sure looks like a pretty new vehicle.  In that sense, it’s a rather rare vehicle.  If this WAS built from new parts, then $25,000 isn’t all that high of price to have someone built a vehicle from scratch.  Including the cost of labor, building a jeep from scratch with new parts would likely land in the $25000 realm.  The ad includes lots of pics.

“You are looking at a titled re-creation of a MUTT M151/ army jeep. In 1999 this Jeep was built in Clearwater, Florida for a jeep enthusiast that had a home in Utah as well. It was shipped to Utah in 2002 and used for local driving and recreational use. This vehicle has also won a few trophies in local car shows. In 2009 the Jeep was shipped back to his home in Palm Beach, Florida where it sat in storage. This vehicle is like new with only 400 actual miles. Everything is in working order and it runs like a 400 mile Jeep should. This vehicle cost over $25,000.00 to have built. There loss is your gain. I am only asking $11,900.00. I am open to all reasonable offers.”

 
To Top

Take apart and put together a Jeep drill

• CATEGORIES: videos • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: This is also known as a “Jiffy Jeep”

I thought I had posted a similar video about a competition; maybe I just saw that video somewhere.  Anyhow, this is a fun video to watch.  Thanks for forwarding it Felix!  If the video doesn’t work, try going here.

 
To Top

1957 DJ-3A Tucson, AZ **SOLD**

• CATEGORIES: DJ-3A • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1600.

“This is a DJ3A jeep that’s had the CJ2A 4X4 Drive train installed. Original 4-134 flathead runs great, T90 3 spd trans and D18 2 spd transfer appear to be good. I drained and replaced the oil and it was Not milky (no water). I took the original (rare) DJ hard top off to use it for hunting, I still have it and it goes with the Jeep. Replaced the rubber brake lines and flush the brake system so it has brakes again. Original 16″ wheels with the spare. It is currently licenced but need the taillights fixed (wires) to be street legal. It’s a cool Jeep, just don’t have the time or money to do it justice (and space).”

 
To Top

1962 DJ-3A Surrey? Kent Island, MD **SOLD**

• CATEGORIES: DJ-3A • TAGS: , , This site contains affiliate links for which I may be compensated.

UPDATE: Was $3600. **SOLD**

This looks good.

“1962 military style, 2 wheel drive, three on the tree, 4 cylinder flat head, rear seat, upholstery in great condition, garage kept past 18 years, 52000. miles, no rust…great shape! A fun ride !!”

 
To Top

1965 DJ-3A Kansas City, KS **SOLD**

• CATEGORIES: DJ-3A • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $4500.

Here’s a DJ-3A in good condition.  I’ve only seen 2 other ’65s.

“Amazing but no rust ever or anyplace. It’s been sitting for a few years and has bad gas in it and doesn’t want to stay running. Flathead inline 4 with floor shift three speed. Fun time at the parade or cruise.”

 
To Top

1954 CJ-3B Silt, Co *SOLD*

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE: Was $2100. **SOLD**

This might be a good price.  The top looks decent.

“54 Willys.Good project jeep. New tires, cloth top, rollbar, gas tank, front seats. Still needs mechanical work”

 
To Top

Year? CJ-2A Ceres, Ca **SOLD**

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2000.

Desert dogs on some old steel rims — classic.

“Has small block chevy engine 4 wheel drive needs work but it runs good if you like to know more 2,000 O/B/O”

 
To Top

MB/GPW Body Parts Bay Area, Ca

• CATEGORIES: Body Parts This site contains affiliate links for which I may be compensated.

No pics.  Not exactly sure what’s here …

“1941 – 1945 WILLYS/FORD SHEETMETAL, I HAVE THE COMPLETE FRONT END, THAT MEANS FROM THE COWL FORWARD, I ALSO HAVE THE COWL, I HAVE FRONT STEER AXLE WITH LEAF SPRINGS, I HAVE EXTRA SPRINGS ALSO. CALL ME AND MAKE ME AN OFFER, ALL SHEETMETAL IS ORIGINAL NOT AFTERMARKET, SHEETMETAL IS IN EXECELLENT CONDITION, FRONT AXLE IS IN EXCELLENT CONDITION ALSO. 605-999-4842 OR EMAIL ME I WILL BE SCRAPPING THIS IF I DONT SELL WITHIN 1 WEEK. I HAVE NO USE FOR IT AND IT IS JUST TAKING SPACE.”

http://sfbay.craigslist.org/nby/pts/1947743538.html

 
To Top

1953 M-38A1 Evanston, WY **SOLD**

• CATEGORIES: M-38A1 • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1700.

Brett spotted this deal.  This includes a Winch!  It looks like a great price.

“This has had a 283 chevy engine swap, it still has the jeep three lever transfercase and the transmission. The engine has new ignition and exhausts. clean older jeep. It also has an 8000 pound winch and a tow bar.”

 
To Top

1953 Wagon Tampa Bay, Fl **SOLD**

• CATEGORIES: Willys Wagons • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2500.

This appears pretty solid for a east coast wagon.  It might be a good price.

“This jeep has been in my family since 1963 and until now its had a place to stay. interior was redone in late 90″s. engine is complete but hasn’t been started in a few years, have some parts also. Willing to take partial trade doe guns or boat.”

 
To Top

1949 CJ-3A Williams, AZ **SOLD**

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $5000

“1949 Willys Jeep. Runs Great. Firm on Price. Only serious inquiries please.”

 
To Top

1948 Jeepster Waller, Tx $6500

• CATEGORIES: Jeepster • TAGS: This site contains affiliate links for which I may be compensated.

This has a Chevy S-10 rear.

“Engine & Transmission – 1980 Camero V6 350 Auto; Rear – 1998 Chevy S-10 Pick up; Interior Black vinyl door panels and seats. Black carpet. Have new top; Asking $6,500.00 OBO; No Title; Contact Bill between 8:00 am and 6:00 pm at 281-777-9005.”

http://houston.craigslist.org/cto/1946553894.html

 
To Top

1954 Truck Mesa, AZ **SOLD**

• CATEGORIES: Willys Trucks This site contains affiliate links for which I may be compensated.

UPDATE:  **SOLD** Was $700

The seller is willing to work on price.  It might be a good source of parts.

“This truck has original frame all tires and body is complete no title does have a AZ plate from 1996 this is a total project Truck or can be used for parts. Has a Chevy Engine 350 small block last time on the Road was 1996 it ran good. We are willing to work on the price. Please come and look if you are interested.”

 

 
To Top

3 CJ-2A Tubs, 1 CJ-3B Tub, and more **SOLD**

• CATEGORIES: Body Parts, CJ-2A, CJ-3B, trailer This site contains affiliate links for which I may be compensated.

UPDATE:  Everything is SOLD .. just here for historical purposes.

“I have 4 Willys Jeeps for sale.

There is are ( 3) CJ2A tubs: 1945 $50, 1946 $250 and 1948 $600.

There is ( 1 ) CJ3B 1954 tub $300. There is 1 complete rolling chassis ( $300 ) that will fit any of the tubs.

 
To Top

1954 Truck Brian Head, Utah **SOLD**

• CATEGORIES: Willys Trucks • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE:  SOLD — listed for $3500

“This truck was used very little only to haul water once a year.  The truck has a  Chevy 327 V8  it is a three speed with a Warn Over Drive, The truck runs and drives.

Continue reading

 
To Top

More from Roberto Flores

• CATEGORIES: Artists/Drawings This site contains affiliate links for which I may be compensated.

Roberto always has a variety of flat fender items attached to shirts, pillows and more.  He forwarded some more pics for us.  You can always check Roberto’s store for more .  You can also check his English language version of his website: http://www.robertoflores.com/ And this blog too: http://theoutliner.blogspot.com/.

Continue reading