Racing Research Archives

To Top

Race Jeep, St. Helens, Or **SOLD**

• CATEGORIES: Racing • TAGS: .

UPDATE: **SOLD** was listed at $3800

(02/15/2011) Looks Fun!

“Flatty body on a boxed cj-5 frame. Dana 44s front &rear, 4.27 gears, dodge 360, dodge top loader 4spd, twin stick jeep 20 t-case, race buckets & harnesses, full roll cage down to the frame, aluminum radiator, msd ignition 6AL box and distributor. More!! Good running, reliable, and very easy on parts. This is a Pnw4wda short 8 class jeep. Turn key race or sand ready!! Not street legal!”

 
To Top

1952 Redmond, OR **SOLD**

• CATEGORIES: CJ-3A, Racing • TAGS: .

Update:  **SOLD** Was $1000

Based on the number on the passenger side, I believe this was raced at one time.  It would have been an Eastern Washington jeep (Region 4).  The top appears in reasonable condition.  It either has a DJ or a CJ-3B windshield.

“1952 Jeep Willys Project….Engine is in the back seat……Donated to us just as you see it…… Call or come see it.”

 
To Top

1946 Flattie Mudbogger Sarasota, Fl $5000

• CATEGORIES: CJ-2A, Racing • TAGS: .

Ready, set, mud.

“1946willys mudbogger buick225 ci v-6,3 speed trans.,rollcage,
racing seats,5 point harness,rear mounted radiator
new 39″ super swamper boggers
wicked fun in the mud hole

price $5,000.00 obo

call 941-915-6971 if no answer leave message”

http://sarasota.craigslist.org/cto/2752130346.html

 
To Top

An Unusual Build Valdosta, Ca $1500

• CATEGORIES: Racing • TAGS: .

Looks a bit odd to me.

“Into all types of guns. Rolling chassis with 4 link front and rear. 3/4 ton rear with 373 gears and full spool. Old fiberglass Willys jeep centered seat body with pro scoop. Body lifts like a funny car for easy access to everything. Full roll cage. Supper cool and gets lots of attention. Mud or sand dragster. Won’t take long to put this one together to race. Asking $1,500 OBO 229-834-544one ”

http://valdosta.craigslist.org/pts/2746891966.html

 
To Top

Sand Drag Jeep Portland, Or $15,000

• CATEGORIES: Racing • TAGS: , .

UPDATE:  This Drag Jeep is still available.  It does not include engine and tranny.

“sand drag jeep one piece all aluminum body car weight 1500 lbs w/o driver currently runs alcohol injected 383 chev w/ lenco 2spd w/reverse holman moody full floater ford 9 inch w/35 spline summers axles this car has top of line parts too much to list will sell turn key or roller minus motor trades possible jeep willys cj5 tractor??? no junk . 503-703-2181 will not respond to e-mail keywords jeepcj5.willys.tractor”

http://portland.craigslist.org/wsc/cto/2695072942.html

 
To Top

1948 CJ-2A El Cajon, CA **SOLD**

• CATEGORIES: CJ-2A, CJ-3A, Racing • TAGS: , .

UPDATE:  Was $7950 **SOLD**

(11/01/2011) This looks like a sand rig of some type.

“This is clearly ONE OF A KIND….. You have to see it !!!! We have a clean title, it is on a non-op now.. If you have any questions please feel free to email me, and I will quickly get you a reply. 1948 Willys RED !!!!! Make me an offer, and please do not low ball me”

 
To Top

Custom Flattie with Frame and Cage Leadville, Co $500

• CATEGORIES: Racing

Now that’s a long front clip!

“’48 WILLYS JEEP ON CUSTOM FRAME WITH FULL ROLL CAGE ONLY. BUILT FOR CHEVY FULL WIDTH AXLES AND CHEVY SMALL BLOCK 350. HAS FRONT LEAF SPRING AND REAR COIL. GREAT START FOR A ROCK CRAWLER!!!!! WHEEL BASE IS 9 FEET!!! 500.00 FIRM!”

http://rockies.craigslist.org/pts/2641992896.html

 
To Top

1956 Sand Drag Jeep Lewiston, Id $4800

• CATEGORIES: CJ-3A, Racing • TAGS: , .

UPDATE:  Price dropped to $4800

(06/16/2011) I don’t see very many sand drag jeeps around Boise.

“I have a nice little willys has paddle tires 5 point harness seats small block 350 bored 30 kamel hump heads torqer intake big cam rum awsome some really good 70 to 75 pounds oil pressure alot of work has been fabricated on this. A must see call for details 2088160449 4800 obo”

http://spokane.craigslist.org/cto/2636802002.html

 
To Top

Fiberglas Flattie Inland Empire, Ca $8,700

• CATEGORIES: CJ-2A, CJ-3A, Racing • TAGS: .

I’m sure this is a fun rig to drive.  I can’t tell if it is street legal or not.

“cj all fiberglass body and tilt front clip has 383 sbc world products heads victor jr intake holley carb roller rockers nice cam fenderwell exit headers / th 350 trans with treans break in it dana 300 transfer case /dana 44 front&rear disc in front locked in rear 355 gears /15×10 m/t wheels&bfg 35s mud treain tires /full cage powder coated /ladder bars /nos / tilt wheel/ps/electric fan/fuel cell/batt in back with kill switch/ runs great /clean pink in hand call for info(559)936-3560 ($8.700) obo trade for harley bagger/older nova/chevelle/camero 67-72/or cash is king”

http://inlandempire.craigslist.org/cto/2614573384.html

 
To Top

1950 M-38 Hot Rod Scottsale, AZ **SOLD**

• CATEGORIES: Jeep Rods, M-38, Racing, Roll Cage • TAGS: , .

UPDATE: **SOLD** Was $16,500.

(10/04/2010) This is a 2WD, street legal jeep.

“1950 Jeep Willys. This is an original (Titled & Registered) 1950 steal body Willys. It has been professionally rebuilt. It is one of a kind, no expense spared, best parts money can buy.

Fresh (new) 600 Plus HP 355 SB Chevy (Nitrous Motor) built by Denunzio Race Engines. New powerglide transmission built by Remac. New Curry Ford 9 inch rear end. New driveline, steering, front end (2WD). New digital 6 plus MSD computer. New seats, yellow top optima battery. NEW EVERYTHING….MINT CONDITION.”

 
To Top

1951 Ice Racer Parker, CO **SOLD**

• CATEGORIES: CJ-3A, Racing • TAGS: .

UPDATE:  **SOLD** Was $15,000

This is offroad (or on ice) only.

“1951 race willys, v8 high performance motor, automatic transmission, trany lock, chipped, rev limitor, msd ignition, all wheel lockers, custom built, 6 sets of ice racing tires, bucket seats, tons of upgrades and performance parts, $15,000 O.B.O”

 
To Top

Parkette Body and Bobcat Hood (& more) Yakima, Wa **SOLD**

• CATEGORIES: Body Parts, Features, Racing, Roll Cage • TAGS: , .

UPDATE:  Last price was $1000. It sold.

The Parkette fiberglass body is an extreme rare, well made body.  One of the best things about this body is that a CJ-3A windshield will properly fit it, unlike the fiberglass Bobcat body.   During the 1970s, a friend of mine bought a Bobcat body, prepped it, and painted it.  When he stuck on the windshield he discovered the cowl was too flat to properly seat the windshield to the cowl.  To say he was angry was an understatement, because he felt he was mislead by the promises the manufacturer made.

So, after talking with the Parkette body manufacturer and getting assurances that the measurements were more accurate, he bought the body and has been happy about it ever since.

The body shownn below has had it’s rear wheel wells cut a bit.  It’s got a good looking rollcage that has been attached to the frame.  If this has been available when I was building biscuit, I would have started right here.

 
To Top

Old Flattie Racer Othello, Wa **SOLD**

• CATEGORIES: CJ-2A, Racing • TAGS: , .

UPDATE: **SOLD** Was $800.

This has some solid lettering Dogs.  It sure looks like a racer from the 80s maybe.

“This is a project rig. It does not run. I don’t know what kind of shape the drive train is in. I found it in a field. I was told it used to be raced and the axles are welded up. I due have a title for it. I can’t remember the year at the moment but 46′ sticks in my head. I was going to build a wheeler out of it but I have no time or money. I’d like to see $800 but feel free to make an offer. I can send more pics. It’s currently in storage in Othello but I live in tri-cities.”

 
To Top

Flatfender Jeep Rod Volusia County, Fl **Status Unknown**

• CATEGORIES: Racing • TAGS: , .

UPDATE: **Status Unknown** 

“1942 Willy’s Flat Fender Jeep – Classic Street Rod!

92″ Wheel base, 350 4-bolt, 400 Chevy trans, NHRA tech rollcage & safety harness, disk brakes, Edelbrock 4 barrel carb & manifold, street & strip gears, 2 rear-end center sections – street & strip, body & frame extended 12″… Too much to list !!!

MUST SEE & DRIVE!!!!! – Will Consider All Offers, Including Trades!”

 

 
To Top

Race Jeep Chassis (FC-150) Randle, Wa $500

• CATEGORIES: Racing • TAGS: , .

UPDATE:  Still Available

(03/08/2011) Here’s an unusual racer that utilized a FC frame.

“Willys Jeep tub and frame.  FC150 frame, custom tub (6″ wider than standard), 2″ roll cage, has leaf springs, steering column, fuel cell, and bucket seats. Mark (360) 497-7504”

http://seattle.craigslist.org/oly/cto/2486173097.html

 
To Top

1952 Sand Drag Flattie Rancho Cucamonga, Ca No Price

• CATEGORIES: Racing • TAGS: , , .

UPDATE: Still Available.  Was listed at $15,000.

(12/08/2010) Looks fun.

“1952 Flat fender jeep, full fiberglass body, Chevy 406cu small block 450 hp, Dana 60 in rear w/locker, Dana 44 in front w/warn hubs, 4-link in rear, fuel cell, 205 transfer case, B&M Trubo 400 w/clutch, B&M cable shifter, disk braks w/hill assist, scatter shields, MSD ignition w/two step rpm limiter, sand tires and garage tires. This is licensed as a 1952 and is current (clean title) ready to dune or do the hill. Call Chris @ 909-944-7173.”

http://inlandempire.craigslist.org/cto/2465414203.html

 
To Top

1942 Sand Jeep Hubbard, Or $4500

• CATEGORIES: Racing • TAGS: .

UPDATE:  Still Available

(06/23/2011) This looks like a classic 70’s Sand Rig.

“1949 Willys cad telescope steering, 72 camaro 350 with 72 camaro 4speed steel crank and rods, grafite pistons, 202 valves, double pumper on and on all new
9″ Ford rear end four link spool 513 gears, 400hp small block, 250 hp nitais, glass hood very fast in sand, look at pics /selling for friend,503-951-8502 call me ill give you his number”

http://salem.craigslist.org/cto/2438796864.html

 
To Top

Chris enters his first PNW Race

• CATEGORIES: Features, Racing • TAGS: .

Now, you probably think I run eWillys because of all the money, fame, babes and glory I receive.  Not true!  Instead, it is a story like this one that makes the work worthwhile.  Nearly two years ago I started swapping emails with 15 year old Chris Ruhnau.  He had a mostly stock 1947 CJ-2A and was having problems with some wiring issues.  We worked through those issues, brake issues, battery issues,  and even a girl issue.  Last summer he spotted a CJ-2A just down the road from him, with a full cage and more for only $1000. He couldn’t resist, so at age 16, he was the proud owner of two jeeps.  Clearly, he suffered from a case of Willys Sickness.

Over the past winter he spent time working on his jeep and going to high school.  This summer, he got everything finished and found his way to his very first PNW event.   As you will read, he had a great time.  Nice work on the jeep Chris and keep on racing!

Dave!!! You’ll never believe this! I raced my jeep today! The PNW4WDA put on a race in Ethel, Wa.  I raced twice in the obstacle course! It was so much fun. I’ve never had so much fun! In both races I got the same time… 1.61. It was really hard though because it was really soupy. I only had 2 problems, my fan wire shorted out and then my battery died, but those are minor and i still had tons of fun. everyone was coming up to me when I was sitting in line and asking about the jeep and saying it was nice. I felt pretty good about that. A guy i know that races said that he’s going to let me take my jeep to his shop and we’re going to fix my steering and he’s going to give me some brand new rancho shocks so that my fenders and battery box wont rub on the tire so much. The guy that used to be the leader of PNW4WDA asked for my email, too, to let me know when the events schedule so I can race a lot this summer!

 
To Top

1953 CJ-3B Gore, Va $3900

• CATEGORIES: CJ-3B, Racing • TAGS: .

This looks like a good price on a nicely customized rig.  Maybe it was even a former ECW4WDA jeep?

“350Engine 400+ HD
350Auto Trans
4 x4 / 536 Gears
Detroit Lockers
Floating Rear Axle
5 Point Harness
2 each high back bucket seats
2 sets Dot tires/chrone wheels
2 sets paddle tires
Steel Roll Cage
Original Seats
Original Gas Tank
Orginial Windsheild
Body no rust no body filler
M.S.T.A.”

http://westmd.craigslist.org/cto/2444571400.html

 
To Top

Drag Racing Jeeps at BillHughes.com

• CATEGORIES: Racing

I ran across the below drag jeep that appears to be streetable based on the brakes lights and the caption on the picture.

See more drag jeeps at BillHughes.com.

 
To Top

Larry Minor Sand Jeep Hemet, CA **SOLD**

• CATEGORIES: Racing • TAGS: , .

UPDATE:  Was $35000. **SOLD**

“For sale is a custom, long-travel, sand jeep. It was built in 2004 by Larry Minor Motorsports using the finest automotive engineering and expertise available in the off-roading market. It is turn-key ready for Glamis fun.

The vehicle has a small block 430 cubic inch Dart after-market engine and produces 700 hp. It has a Turbo 400 transmission and a Strange Spool 9 inch Ford rear end. The body is full-fiberglass with a chromoly tube frame. It has been molded after a 1946 flat fender Willy’s Jeep.”

 
To Top

Sand Jeep @ Silver Lake in 2009

• CATEGORIES: Features, Racing

I spotted this great shot from Quadratecforum.com.

According to the post, his is a sand Jeep. It was the annual Mt. Baldy hill climb Spring 09. (Silver Lake State Park.) This thing was wicked. Easily won the class. He could stand it up at will and ride it as long as he wanted. Frickin awesome!”

 
To Top

Race / Sand Drag Flattie Oregon **Status Unknown**

• CATEGORIES: Racing • TAGS: , .

UPDATE:  Was $5500. **Status Unknown**

(07/16/2010) My only question is, why park it facing a tree for pics?

“Built 355 Chev. 800 plus hp Sand Dragger – Hill Climber! 1956 Willys flat fender, body and frame. Narrowed and lengthened. All fiberglass body. 4-wheel drive capability, with automatic hubs. 1000 plus CFM, Holly double pumper, Holly fuel pump and fuel regulator with pressure gauge. Custom flowed heads with roller rockers and girdles. Roller lifters and diamond pistons. High volume oil pump with extra deep pan. Power glide, 2-speed trany, with 6500 ratchet stall converter. Trany lock-out micro switch and ratchet shifter. Aluminum radiator with switches for fan, trany fan, water pump, fuel pump, ignition. Locker rear end with new Strange axles. 20.00 – 15 comp. cut paddle tires and Mitchell triple laminated aluminum rims. Sturdy, weighted triangular wheely bar, Mallory tack with rpm limit and shift light. Raced in B-Comp Modified Class! Never used nitrus, Fuel used is C-12. Geared for 100 yds. in 4.5 seconds. This rig is testosterone on steroids!!!! Proven Record of consistency.”

 
To Top

Finally, Just Some Soda Pop

• CATEGORIES: Features, Racing

I think this builder couldn’t decide between Coke or Pepsi.  I found it at jeepfan.com.

 
To Top

Old Racer Pennsburg, PA **SOLD**

• CATEGORIES: Racing • TAGS: .

UPDATE: **SOLD** Was $500

Here’s an old racer with a nice cage.

“Old Willys race jeep. been sitting a long time. No motor or trans. $500.00. NO SCAMMERS!!”