On Sunday, I was able to tack together the basic structure of the rear portion of the cage. On Monday, I began work on the front portion.

Here’s a look a the back portion with the body sitting on the frame:

There are still a number of small things to do to complete the rear portion (such as adding rear shock mounts, adding some corner supports, and, of course, welding all the connection points).

To properly calculate the two long side bars, which will run from the mid part of the frame back to the rear loop, I needed the body to be sitting on the frame.

Each side bar has four bends, so getting them both the same is a good challenge.

After LOTS of measurements, angle considerations, and design thoughts, I finally got around to bending the two most difficult angles on the side bar. Below you can see the passenger side bar temporarily in position, though the lower two bends haven’t been finished yet (next bend will direct the bar vertically at the dash, then the final bend will redirect the bar forward under the dash where it will attach to a still-to-be-added cross bar.

Unfortunately, I didn’t get as far as I’d hoped, because Ann had a bad migraine, so I had to take the dogs to the groomers (which they needed pretty badly, as bad weather forced us to cancel two previous appts over the past two months).

I expect that by Friday I’ll have all the bars bent, positioned, and maybe even welded.

Bad cows …

I had big plans to work out early and get out to the shop. But, just as I finished my lifting, our neighbor Andrew texted me at 7:30am, “I got a text from my neighbor Dan Green. Your cows are in his pasture.”

Ugh. There went my early start in the shop.

We piled on clothes (below freezing this morning), loaded up the UTV, and headed over to Andrew’s fence line (the cows have been borrowing Andrew’s pasture). Sure enough, the cows had created a nice wide entrance in the wire fence.

The moment the cows heard our UTV, they recognized it was feeding time, so we lured six of them back to Andrews pasture. Of course, one dumb cow, our 7mo steer, couldn’t figure out how to get back through the fence, so, of course, he went over another part of the non-barbed wire fence, damaging it. Ugh.

Once at Andrew’s pasture, we wooed them over to our pasture with food and closed the access gate to Andrew’s place. With the cows grounded, we went to work on the fence.

Thankfully, it didn’t take too long to fix the fence. I.believe our two mischievous 2yo steers (they become meat next month) were leaning over the fence to get some tall grass in Dan Green’s pasture, which caused the fence to collapse. Bad cows.

Now for the cage progress. I’ll skip the explanation (am tired) and just get straight to the pics. The big loop is completed, along with the back bars and the rear cross bar. Everything is, level, square, tacked-in-place, and ready for more bars.

There will be no work on Friday (quick trip to Seattle), but I plan to get back to it this weekend. I’ll add more bars for strength, then begin work on the front loop.

More-months-than-I-care-to-think-about ago (about seven months I think), I bought a cheap Affordable Bender. When it arrived, I was less than impressed with the collar (see this post). So, I called them, only to learn that the collar was designed that way and should work fine (I believe they told me “Billions” of bends have been done with Affordable Benders, or something like that).

So, I decided to test the bender before sending it back; I hadn’t expected to wait 7 months to test it!

Yesterday, I mounted it to my metal work table and tested it with a 90 degree bend, one of two I need for the racer’s main loop (it’s the most difficult bend of the entire roll cage). The bender comes with a 90 degree die, so I was a little worried wether the bender would do a 90 degree bend.

First off, it didn’t take me long to miss my old bender, the one I built from plans: http://www.ewillys.com/2009/10/08/my-tube-bender-almost-done/. But, since I couldn’t access my plan (lock PDF with no password and the author of the PDF wouldn’t answer my emails), I had to buy this AFF bender.

Here are the results of the 90 degree bend .. as you can see, it stops short of a 90 degree bend:

Ugh .. what It meant is that I had to force the 15′ tube through the collar a few inches so I could add an additional bend. While that worked, I bent it too far (I misread my level .. it went to 90 degrees which I missed, then started down to 88, so I thought it was at 88 and needed to go to 90. UGH .. had to start over).

Eventually, I got the hang of how to do a 90 degree bend with this and managed to create the loop below.

This pic shows the first 90 finished and I’m starting on the second.

This shows the second 90 done. That is all the 90s I need, so the rest of the bends should be much easier.

I still have two more bends on this loop (the bars are parallel, though don’t look that way in the pics), which I’ll complete tomorrow.

I’ve spent parts of the last couple of days thinking through how/where the new cage will attach, how the floor should attach, and how the body should attach and where it should sit. For example, the body must be far enough forward so that the solid front clip can slip over the front of the radiator, but back far enough to sit in the right area in the back.

My initial intention was to bolt the cage fo the frame, but this frame (already cut and spread 5″) has enough mods that if I’m at a point that the cage has to be removed to make changes, I’m better off starting with a new frame (and, at this point, I don’t want to do a ground up rebuild).

Additionally, the body has warped some, so I will need to build a jig out of wood so that I can try to straighten the body some (apparently, using a heat gun, I should be able to remove some of the warping. What I can’t re-straighten, I will use fiberglass and/or some (probably) aluminum plates placed strategically to make it look straighter.

Here’s a couple pics of the body. You may not be able to tell, but both sides of the front of the body have flexed outward. So, between the heat gun, the jig, some interior plating, and the use of strategic mounts, I should be able to make it look a little less out of whack.

Over the next week we are supposed to have (finally) dry weather and temps that will be in the high 40s and low 50s, so I hope to get the cage built and, maybe, the body cleaned up to ready for some fiberglass repair and, eventually, some paint.

Though I dislike the neon green chassis, Ann has acquired a taste for it, so I might start with the body painted black, similar to the narrow body that was on it.